Support
Machine type
Brand
Brown PonyXprs Manual Screen Printer and Conveyor Dryer

Brown PonyXprs troubleshooting: belt stalled, low or no heat, fan not working, and printer wear parts

✓ Reviewed by Jason KimUpdated 2 min readFits: PonyXprs · Pony dryer
Short answer

If the dryer belt stalls, Brown says to check the power connections and fuses first, then the drive chain and sprocket, then the motor controller and drive motor. For low or no heat, check the power connections, then whether your shop voltage is dropping, then the temperature selector switch and heater panels. A fan that won't run is either a power connection or a failed fan. Electrical testing is for a qualified electrician.

Disconnect and lock out all power before opening any electrical enclosure. Brown says suspected electrical problems should be handled by a qualified electrician or electronics technician, who reapplies power only for testing after inspecting the open enclosure.

Brown's chart

Work down each list in order.

Conveyor belt stalled

Cause Fix
Power connection Check power connections and fuses
Loose chain or sprocket Adjust or reconnect
Motor controller Replace
Drive motor Replace

Exhaust or forced air fan not working

Cause Fix
Power connection Check power connections
Failed fan Replace

Low heat or no heat

Cause Fix
Power connection Check power connections
Voltage drop From heavy load in your area: a boost transformer may be needed. From your building wiring: larger supply wire may help.
Selector switch Replace the temperature selector switch
Heater panels Replace the one that isn't working

What you can check yourself

  1. Plugs and breakers

    Make sure each plug is fully in its outlet (the PD-2006/120 needs two), the shop breakers are on, and the breaker switches on the dryer panel haven't tripped.

  2. Pilot light

    With the heater switch on, the pilot light should be on. Note what it does; we'll ask.

  3. Forced air switch

    If the forced air fan seems dead, make sure the Forced Air switch on the panel is actually on. It is a separate switch from main power and the heaters, and Brown only turns it on when a job needs it.

  4. Chain and sprocket

    With power off, look at the belt drive chain. If it's loose, off the sprocket or packed with lint, brush the lint out with a stiff brush and contact us about adjusting it.

  5. Belt tension

    A belt that's too loose slips; one that's too tight strains the motor. See our dryer settings guide.

Printer wear items

  • Knobs and lifters wear with normal use and are replaceable.
  • Platens are melamine coated press board. Too much heat warps them.
  • Lint and spray adhesive make parts bind. A clean machine lasts longer.

Before you contact us

Have these ready so we can help faster:

  • Your dryer model from the tag (PD-2004, PD-2006/120, PD-2006/240 or PD-2407) and your shop voltage
  • Which problem from the chart you have, and which checks you have already done
  • Whether the pilot light comes on with the heater switch on
  • Whether the belt, the heat or the fan stopped suddenly or faded over time

Brown also notes that a dryer can under cure even when the panel looks normal, so keep checking cure during production. Text us a photo of the control panel and a short video of the problem at (562) 609-4996.

Common questions

The belt stopped but the heat is still on. What do I do?

Turn the heaters off right away so nothing scorches, then work through the belt checks with the power off.

The heat is weak only at busy times of day.

Brown points to voltage drop. If it comes from heavy load in your area, a boost transformer may be needed; if it's your building wiring, larger supply wire can help. Have an electrician confirm.

Can I test the controls myself?

Brown says a qualified electrician or electronics technician should do it: lock out power before opening any enclosure and only reapply power to test after inspecting.

My platens are warping.

The standard platens are melamine coated press board and warp if they get too much heat, for example from a flash. Replacement tops are available.

What wears out on the printer?

Brown lists knobs and lifters as normal wear and tear.

Did this fix it?