Support
Machine type
Brand
Epson SureColor F2270

Epson F2270 daily, weekly and monthly maintenance, step by step

✓ Reviewed by Jason KimUpdated 3 min readFits: F2270
Short answer

Every working day, rock the two White ink packs about 25 times, print a nozzle check and run Auto Cleaning or a Light cleaning on any channels with gaps. Every week, clean the suction cap. Every month, rock the color packs about 5 times and check for firmware and Garment Creator 2 updates. Unlike the F2100, Epson recommends leaving the F2270 switched on, because it runs a cleaning every time it powers up.

Every working day (about 5 minutes)

  1. Rock the White ink packs

    The screen prompts you every 24 hours. Open the ink cover and pull the white ink tray out, with one hand under it so it doesn't drop. Rock it in a seesaw motion at about 60 degrees, about 25 times in 25 seconds, gently, then push it back in. Repeat for the second white pack. Tap the message and choose How To... to see it on screen.

  2. Print a nozzle check

    Set Platen Gap to Auto, bring the platen forward and remove the frame. In White ink mode tape transparent film or colored paper to the center of the platen (letter size on L, M or S platens). Set the height lever to P, then choose Menu > Maintenance > Print Head Nozzle Check, check the settings match your platen, and select Start.

  3. Clean if you see gaps

    Choose Menu > Maintenance > Head Cleaning > Auto Cleaning first. If gaps remain, run Cleaning (Light) on the rows with gaps, then Medium. If Light and Medium haven't cleared it after a few tries, clean the suction cap before you use Heavy. If it's still clogged after that, clean around the print head.

Every week (5 to 10 minutes)

Clean the suction cap: Menu > Maintenance > Cleaning the Maintenance Parts > Suction Cap > Start, then follow How To... on screen. Use only the plastic tweezers that came with the printer. Wipe the edges of the cap until you can see the cap's own color again, because dirt left on the edge breaks the seal and weakens suction. Don't scrub hard: scratches cause air leaks. If a cleaning stick gets dirty, rinse it in ink cleaning solution or use a new one. A buzzer sounds 10 minutes after the head moves out. Finish quickly, select Done and print a nozzle check.

Epson's warning signs that the cap is overdue: cleanings stop changing the nozzle check, or there's no visible ink flow through the right-side maintenance tube during a Medium cleaning. If the printer sits idle, turn it on at least once every 7 days and print a nozzle check.

Every month (about 5 minutes)

Rock each color ink pack the same way, about 5 times in 5 seconds. The Maintenance Liquid and Cleaning Liquid packs don't need shaking. Then check Epson's F2270 support page for firmware and Garment Creator 2 updates, and keep the two on matching current versions.

When the printer asks

Message What to do
Head cleaning set at end of service life Replace the wiper unit, capping station and flushing pad, in that order, all at once. Start from the message or Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set. Make sure the flushing pad hooks sit flat. You can't print until all parts are replaced.
It is time to clean the sensor cover Select the message, then Cleaning, and follow How To.... If water doesn't remove the ink stains, use ink cleaning solution.
It is time to clean the Encoder Scale Move the platen in, turn the printer off, put about 5 ml of ink cleaner in the cup, soak a wipe and gently pinch the strip, wiping each way 2 or 3 times. Don't touch the carriage shaft. Dry it with a clean cloth.
Waste ink bottle at end of service life Swap the bottle, seal the old one with the caps from the new one, and select OK to reset the counter.

Use ink cleaning solution only on the parts Epson lists (suction cap, around the head, sensor cover, encoder strip, and the platen without a grip pad). Never reuse solution you've already cleaned with, and never move the head or platen by hand.

Stuck on a step? Text us a photo or short video at (562) 609-4996.

Watch Epson's video: cleaning the F2270 suction cap

Embedded from the manufacturer's official channel.

Common questions

Should I turn the F2270 off at night?

Epson recommends leaving it on. The printer runs maintenance every time it turns on, so turning it on and off often uses more ink. If you do switch it off, use the power button, never a power strip or breaker.

What does Auto Cleaning do?

It checks the nozzles itself and then cleans at the strength it decides is needed. You can set when it runs under Menu > General Settings > Maintenance Setting, including whether a clog threshold stops printing, shows an alert or triggers a cleaning.

I can't see the white rows on my nozzle check.

In White ink mode Epson says to print on transparent film or colored paper. White doesn't show on plain white paper.

The white is still weak after several cleanings.

Epson's next steps: run Cleaning (Heavy) on all the WH rows once or twice, then switch the printer to Color ink mode and back to White ink mode. If that doesn't fix it, contact us.

Can I use my F2100 maintenance kit on the F2270?

Yes. Epson lists the same printer maintenance kit, part C13T736200, for both printers.

Did this fix it?