Support
Machine type
Brand
Epson SureColor F2100

Epson DTG pretreatment for the F2100 and F2270: dilution, application and heat press settings

✓ Reviewed by Jason KimUpdated 2 min readFits: F2100 · F2270
Short answer

Epson's cotton pretreatment must always be diluted with distilled or purified water. If you fix ink with a heat press, start at 1:1 and test up to 1:3. With a heat tunnel, start at 1:2. Apply it evenly to an area larger than the print, then press it dry at 338°F for 45 seconds (up to 90 for big prints) under parchment paper before printing. Too weak and the white won't hold. Too strong and it leaves marks or cracks after washing.

Which pretreatment

Epson's Cotton Pre-Treatment Fluid (C13T43R100) lists the F2100 and F2270 as compatible, along with the F2000 and F3070. It's for cotton and cotton-rich shirts. The F2270 can also print polyester with Epson's Polyester Pre-Treatment (C13T43R200), for shirts that are 50 to 100% polyester. You need pretreatment whenever you print white ink. Without it, Epson says white won't appear correctly or stick, and colors printed on top won't develop.

Dilution

Pretreatment and setup Epson's starting ratio (pretreatment : water)
Cotton, ink fixed with a heat press Start at 1:1 and test up to 1:3. Epson suggests 1:2 for letter-size prints or smaller and 1:3 for larger prints
Cotton, ink fixed with a heat tunnel Start at 1:2 and test up to 1:3
Polyester (F2270), printing with white Use it straight, undiluted
Polyester (F2270), printing without white 1:6

Always test on a part of the shirt nobody will see before treating the whole print area. Mix only what you need for the job: Epson notes leftover mixed solution can harden.

Applying it

  1. Lint-roll the shirt

    Remove lint from the print area with sticky tape or a lint roller first. Lint left under the pretreatment causes uneven prints.

  2. Roller method

    Use a short-fiber polyester paint roller and a separate roller for each shirt color, so dyed fibers don't transfer. Soak the roller, squeeze the excess out against the tray edge, and roll evenly in both directions over an area larger than the print. Finish rolling shoulder to shoulder, which lines the fibers up with the direction the print head moves.

  3. Sprayer method

    Follow your sprayer's manual. Epson suggests a dial setting around 30 to 45 on a 1 to 100 scale, and about 15 grams (0.5 oz) for a letter-size area. Wear a mask, eye protection and gloves, ventilate the room, and keep the sprayer away from the printer, because the mist can get inside and damage it.

  4. Don't overdo it

    Too much pretreatment lowers print quality. On light shirts, let the pretreatment air dry before pressing to avoid stains.

Pressing it dry

Pretreatment Temperature Time Pressure
Cotton, letter size or smaller 338°F 45 seconds about 6 psi
Cotton, larger than letter 338°F 45 to 90 seconds about 6 psi
Polyester (F2270) 266°F 60 seconds 4.4 psi

Always press with parchment (silicone) paper or a Teflon sheet on top. Pressing flattens the fibers, which is what gives you an even white. Even if you cure ink in a heat tunnel, Epson says to press the pretreatment with a heat press before printing. If the shirt isn't completely dry after the suggested time, keep going while you check it. Your press must be bigger than your platen and able to hold 338°F for 90 seconds. Check it with a probe, since above 356°F colors turn dull.

Keep pretreated shirts dry. If one has sat in a humid room, Epson says to press it again right before printing: 10 to 25 seconds on the F2100 guide, 5 to 10 seconds on the F2270 guide. Never pour pretreatment into the printer's waste ink bottle, because it solidifies when mixed with waste ink.

Storing pretreatment

Keep it at room temperature out of direct sunlight, with the box's tap side up. If white clumps appear in cotton pretreatment, filter it through Epson's funnel and filter before use, and use filtered solution within four days. Turn a new box of polyester pretreatment five times right, five left and five right again before opening. Questions about your shirts? Text us at (562) 609-4996.

Epson's video: how to pretreat a shirt for DTG printing

More videos

Epson: how to pretreat a T-shirt, step by step

Embedded from the manufacturer's official channel.

Common questions

Do I need to pretreat every shirt?

Only when you print white ink. Epson says light shirts printed without white don't need pretreatment. On the F2270, polyester shirts need the polyester pretreatment either way.

What water should I mix it with?

Distilled or purified water. Epson's F2270 guide notes that some components in tap water can cause the cotton solution to coagulate.

Can I use another brand of pretreatment?

Epson notes that using non-Epson pretreatment may give poorer color, image quality or washability. If you use another brand, follow that maker's mixing and pressing instructions.

My white prints look uneven or blotchy.

Check the pretreatment first: applied evenly, not over-diluted, fully dry, and pressed hard enough to flatten the fibers. Epson also warns the press cools down when you run several wet shirts in a row.

What about 50/50 cotton and polyester blends?

On the F2270, Epson says either the cotton or the polyester pretreatment can be used on a 50/50 blend, with some difference in results. Test both on your shirt.

Did this fix it?