Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F2100 banding, blurry or grainy prints and ink spots: how to fix them
Lines, blurry edges, doubled text and graininess on F2100 prints usually come from one of three things: clogged nozzles, a platen set too low so the shirt sits too far from the head, or a print head that's out of alignment. Print a nozzle check first, then set the platen height correctly and run Head Alignment. Ink spots outside the design usually mean lint and ink have built up around the head or on the platen frame.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Horizontal lines (banding), light or dark | Clogged nozzles or feed setting | Steps 1 and 5 |
| Blurry edges, doubled text, grainy image | Shirt too far from the head | Steps 2 to 4 |
| Vertical lines don't line up | Head alignment | Steps 3, 4 and 6 |
| Ink spots or smudges outside the design | Lint and ink around the head or on the platen frame | Spots and smudges, below |
| Grainy color on a white shirt | Low image resolution | Step 6 |
| White edges blurry or white looks weak | Pretreatment too diluted, or nozzles | Our white ink guide |
Step by step
-
Print a nozzle check
Press the maintenance button, choose Nozzle Check and press OK twice. If channels are missing, clean those channels starting at Light. If the problem is grainy output, Epson also lists cleaning the suction cap as a first step.
-
Set the platen height
If the shirt is too far from the head you get banding, blurry edges, doubled lines and grain. Starting positions with spacers a and b on: 3 for T-shirts, 4 with a grip pad, 3 for the sleeve or medium-grooved platen (spacer b only), 8 for sweatshirts and thick fabric. The best height is one step lower than the first position that shows Ready. Seams, collars, zippers and pockets need a lower setting. A quick test: print once in Uni-Directional. If it suddenly looks sharp, the height is off.
-
Run Head Alignment
Install the medium platen with spacers a and b, remove the frame, tape a letter-size sheet to the center and set the height lever to 1. Choose Printer Setup > Head Alignment, select the medium platen and press OK twice. For each color, pick the pattern number with the least white space between lines. If none looks best, choose 1 or 13, whichever is better, and run it again.
-
Fine-tune with Offset Head Alignment
Each step of platen height is +3, and you subtract the garment thickness (1 for most T-shirts). At height 3 on a normal T-shirt that's +6 minus 1, so set Printer Setup > Offset Head Alignment to +5.
-
Adjust the feed for banding
If lines remain, go to Printer Setup > Feed Adjustment (from -1.00% to +1.00%). Choose a higher number if you see dark lines, a smaller number if you see faint lines.
-
Still lines or grain?
Set Head Move Direction to Uni-Directional in Garment Creator or the printer's menus, then try a higher print quality setting in Garment Creator. For grain, aim for about 360 dpi image resolution or print smaller. For color-only prints on white shirts, try Ink Blot Reduction mode in Garment Creator.
Spots and smudges
Epson traces ink outside the print to leftover ink on the platen frame or top plate, or lint and ink built up on the print head.
- Clean around the head: Maintenance > Cleaning around head > Yes. Put a tray or paper under the head, wipe the front, back, left and right edges with a large swab soaked in ink cleaning solution, and never touch the nozzle surface. Finish within 10 minutes.
- Clean the platen path: turn the printer off and wipe the metal borders beside the wiper unit and flushing pad with a soft cloth dampened with water and wrung tight, then dry them. Don't press on the gears.
- Lint-roll each shirt and press the fibers flat with a hard roller before printing.
- Carry printed shirts to the heat press carefully. The ink is still wet.
Also check the basics: the printer cover stays closed while printing, cartridges are genuine Epson and within date, and the white cartridges get their daily shake. Still stuck? Text us a photo of the print and your nozzle check at (562) 609-4996.
Watch Epson's video: cleaning around the F2100 print head
Embedded from the manufacturer's official channel.
Common questions
It printed fine on the same settings last week. Why the banding now?
Start with a nozzle check, because a partly clogged channel is the most common change. If the check is clean, look at the shirt: a thicker garment or a seam under the print raises the surface, and the platen height needs to change with it.
Should I just print everything in Uni-Directional?
Only if alignment doesn't fix it. Epson recommends Bi-Direction (High Speed) for normal printing, and Uni-Directional is noticeably slower.
Do I need to redo Head Alignment when I change platens?
Head Alignment is stored per platen size. If you change platen height instead, use Offset Head Alignment: each step of platen height is worth +3.
What is ink mist and why does it matter?
When the shirt sits too far from the head, fine ink droplets drift inside the printer. Epson warns that a wrong platen height causes ink mist to build up inside the machine, and its maintenance guide notes the mist coats the encoder strip and air filter.
My prints look different from my screen.
Epson notes monitors and printers produce color differently. Design in sRGB, which is closer to the printed result, and judge color from a test print.
- Epson F2100 User's Guide: Overall print quality is poor
- Epson F2100 User's Guide: Grainy or unclear printout
- Epson F2100 User's Guide: Lines are misaligned
- Epson F2100 User's Guide: Ink stains outside the printed areas
- Epson F2100 User's Guide: Adjusting the height of the platen
- Epson F2100 User's Guide: Aligning the print head
- Epson F2100 User's Guide: Fine-tuning print head alignment
- Epson F2100 User's Guide: Printer Setup menu
- Epson F2100 User's Guide: Cleaning around the print head
- Epson F2100 User's Guide: Cleaning the platen path
- AA support requests about F2100 banding, dark lines and spots, 2024 to 2026











































































