Support
Machine type
Brand
Epson SureColor F2100

Epson F2100 clogged nozzles and weak white ink: how to fix them

✓ Reviewed by Jason KimUpdated 2 min readFits: F2100 · F2000
Short answer

Most F2100 gaps and weak white come from settled white ink or a dirty suction cap, not a failed print head. Shake the white cartridges every working day, print a nozzle check, and clean only the channels with gaps, starting at Light. If Light and Medium don't clear it, clean the suction cap before you try Heavy. If white is still missing after that, run Tube Washing for the white line.

Match your symptom

What you see Most likely cause Go to
Gaps in one or two colors on the nozzle check Partial clog Steps 1 to 3
White channels still blank after several cleanings Dirty suction cap, or settled ink in the white line Steps 4 and 5
White looks thin or patchy on the shirt, nozzle check is fine Usually pretreatment, drying or settings, not the head See the last question below
"Suction Error" message Suction cap needs cleaning Step 4. If it keeps coming back, contact us
The printer asks for tube washing Scheduled white-line maintenance Step 5

Step by step

  1. Shake the white cartridges

    White ink is heavy and settles. At the start of every working day (the printer reminds you), take out each white cartridge and shake it for about 15 seconds, flip it over and shake again, then put it back. The printer also circulates white ink on its own, but that doesn't replace the daily shake.

  2. Print a nozzle check

    Tape a sheet of plain letter or A4 paper to the center of a medium platen, then press the maintenance button and choose Nozzle Check. Use clear film or colored paper to see the white rows. Take a photo of it. We'll ask for it if you contact us.

  3. Clean only the channels with gaps, starting at Light

    Choose Head Cleaning > Selected Nozzles, pick the channels with gaps, and run Light. Print another nozzle check. If gaps remain, run Medium.

    Don't jump to Heavy. Every cleaning uses ink and fills the waste bottle. If Light and Medium haven't worked after a few tries, clean the suction cap first (step 4).

  4. Clean the suction cap

    Choose Maintenance > Head Cap Cleaning. Peel off any dried ink film with the plastic tweezers from the maintenance kit. Wipe the inside of the cap with a thin swab dampened with ink cleaning solution, rolling the swab as you go, then wipe the outside and top edge with a large swab. Keep cleaner off the anti-drying caps. A buzzer sounds after 10 minutes, so work steadily, then close the cover and print a nozzle check.

    Never use water or alcohol, never touch the carriage shaft, and don't move the print head or platen by hand.

  5. Still no white? Wash the white ink tubes

    Choose Maintenance > Tube Washing > White Ink. For the white line you'll need two white cartridges and two cleaning cartridges, and possibly a fresh waste bottle. Make sure you have enough cleaning cartridges before you start: if they run short partway through, the printer locks until new ones go in.

When it's not something you can clean

Contact us if any of these happen. They usually mean a part needs replacing:

  • "Suction Error" keeps coming back even after you clean the cap.
  • During a Medium cleaning, no ink moves through the maintenance tube on the right side.
  • Cleanings make no difference at all, even after the cap and tubes are done.
  • The printer shows "Maintenance Request" or "Call For Service" with a code. Write the code down.

Watch Epson's video: cleaning the F2100 suction cap

Embedded from the manufacturer's official channel.

Common questions

How many head cleanings should I run?

Start with Light on just the channels that have gaps, then Medium. If several Light or Medium cleanings don't clear it, stop and clean the suction cap before using Heavy. Epson only calls for a full cleaning when more than 3 nozzles in a row are missing.

Why can't I see the white rows on my nozzle check?

White doesn't show on white paper. Print the check on clear film or colored paper, or straight onto the platen.

Can I clean the cap with water or alcohol?

No. Water and alcohol make the ink solidify. Use only the ink cleaning solution from Epson's maintenance kit, and only on the suction cap, the encoder strip and around the print head.

I'm not printing for two weeks. What should I do?

Print a nozzle check at least once a week, or swap the white ink for cleaning cartridges (Maintenance > Replace White Ink). For a month or more, use Storage Mode. Epson warns that skipping it can leave clogs that can't be cleared.

My white looks fine on the nozzle check but weak on the shirt. Is it the printer?

Often not. Check that the pretreatment is even and correctly diluted, that it was fully dried in the heat press, the white density setting in Garment Creator, and the expiry date on the white cartridges.

Did this fix it?