Support
Machine type
Brand
Epson SureColor F2270

Epson F2270 head cleaning set: when it's due, what's in it and how to replace it

✓ Reviewed by Jason KimUpdated 2 min readFits: F2270 · SC-F2200 Series
Short answer

Replace the F2270 head cleaning set when the screen says it's at the end of its service life, or earlier from Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set. Press Start, then How To... and follow the on-screen steps, replacing the wiper unit, then the capping station, then the flushing pad. The printer won't print until all three are replaced. Tap the head cleaning set status on the home screen to see the exact model number to order.

How you'll know it's due

The F2270's home screen shows the status of the head cleaning set. When a notification icon appears there, the set is nearly worn out. Tap that area to see the model number of the kit your printer needs, and order it then. When the message says the head cleaning set is at the end of its service life, printing stops until you replace it.

Epson's parts list names the F2270 print head cleaning kit as part C13S400216, made up of a wiper unit, a capping station and a flushing pad. Some kits sold for other Epson models look similar but contain different parts. Check the model number on your screen before you order, or text it to us and we'll confirm.

Have these ready

  • The new head cleaning set
  • Gloves and protective eyewear (Epson also says to wear a mask)
  • The maintenance kit, cleaning wipes and tweezers that came with the printer
  • A metal or plastic tray for the used parts
  • A soft cloth

Replacing it

  1. Turn the printer on

    Turn on the printer if it's off.

  2. Start from the message or the menu

    If the end-of-life message is showing, select OK. To replace it early, go to Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set. A confirmation message appears.

  3. Press Start

    Select Start. The platen moves to the maintenance position. Don't move the print head or platen by hand; Epson warns it can cause a malfunction.

  4. Follow the on-screen steps

    Select How To... to view the steps for your printer and follow them on the screen.

  5. Replace the parts in order

    Replace all three parts in this order: the wiper unit, then the capping station, then the flushing pad. After you replace the wiper unit, the print head moves to the maintenance position.

  6. Lift the flushing pad gently

    Ink can fly out if you raise the old flushing pad too quickly. After fitting the new pad, check it's seated correctly. If its hooks are raised when the printer prints, the print head can be damaged.

  7. Finish and check

    Complete the on-screen steps, then print a nozzle check before your next job.

The buzzer sounds 10 minutes after the head moves, and again every 10 minutes. Press OK to keep working, but finish as soon as you can: the nozzles can clog if the head stays uncapped.

Throwing away the old parts

The used wiper unit, capping station and flushing pad have ink on them. Bag them, keep ink off your skin, and dispose of them under your local rules for ink waste.

If something's not right afterward

  • The message doesn't clear: make sure every part was replaced, and that you started from the message or the Replace Maintenance Parts menu.
  • Nozzle check has gaps: run your normal head cleaning routine, then clean around the print head and the suction cap as Epson describes.
  • An error code appears: write it down and text a photo of the screen to (562) 609-4996.

Common questions

What's in the F2270 head cleaning set?

Epson lists the print head cleaning kit as a wiper unit, a capping station and a flushing pad. Replace all three.

How do I know which kit to order?

When the warning icon appears, tap the head cleaning set status area on the printer's home screen. It shows the model number. Send that to us and we'll match it.

Can I change it before the message appears?

Yes, but start it from Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set, or the printer's warning system won't track the new parts correctly.

Why does the printer beep while I'm working?

A buzzer sounds 10 minutes after the platen and head move to the maintenance position, and again every 10 minutes. Press OK and finish quickly, because the nozzles can clog if the head is left out too long.

Can I print with the old parts until the new kit arrives?

Once the end-of-life message appears, no. Epson says you can't print until the parts are replaced, so order at the first warning.

Sources
Did this fix it?