Support
Machine type
Brand
Epson SureColor F2270

Epson F2270 weak white ink and prints coming out too dark: how to fix them

✓ Reviewed by Jason KimUpdated 3 min readFits: F2270
Short answer

For weak white on the F2270, rock the White ink packs daily, print a nozzle check, and check the pre-treatment is even, not over-diluted and fully dried. If white is still thin, run Cleaning (Heavy) on all the WH rows, and after one or two tries switch to Color ink mode and back to White ink mode. For prints that come out too dark, print Garment Creator 2's Ink Density chart on the same shirt and enter the best block's values.

Match your symptom

What you see Most likely cause Go to
White under-base thin, patchy or see-through on dark shirts Settled White ink, pre-treatment or pressing Steps 1 to 4
White rows missing on the nozzle check Clogged White nozzles Step 2, then step 5
Whole print darker than the screen, colors muddy or bleeding Ink density too high for that shirt, or the head too far from the shirt Steps 6 and 7
White shows outside the edges of the design Under-base area too wide Step 7
White still thin after everything Sediment in the White ink path Step 5

Step by step

  1. Rock the White ink packs

    Do it at the start of every working day or every 24 hours, or when the screen asks. This is the single most common reason for weak white. Our F2270 daily maintenance guide shows the motion.

  2. Print a nozzle check on film or colored paper

    Choose Menu > Maintenance > Print Head Nozzle Check. White doesn't show on white paper. If white rows have gaps, run Auto Cleaning, then Light, then Medium on those rows, and clean the suction cap before you reach for Heavy.

  3. Check the pre-treatment

    Epson lists three pre-treatment causes of weak or blurry white: applied unevenly, diluted too much, or not dried completely. Roll off lint before you pre-treat, apply an even coat, and press until the shirt is fully dry. If a treated shirt has been sitting, press it for a few seconds right before printing to drive off moisture.

  4. Check the heat press

    A press loses temperature when you press pre-treated shirts one after another, so check it hasn't dropped. Too little pressure leaves the fibers standing and the white uneven. Also check the White ink packs aren't past their date or more than a year in the printer.

  5. Run Heavy on the White rows, then a mode round trip

    If white is still thin, choose Menu > Maintenance > Head Cleaning > Cleaning (Heavy) > Select Nozzles, select all the WH rows and select OK. If it's still thin after one or two runs, change Menu > General Settings > Printer Settings > Printer Mode to Color ink mode, then back to White ink mode. You need two Cleaning Liquid packs to go to Color ink mode and two White ink packs to come back. If that doesn't fix it, contact us.

  6. Set the ink density for the shirt you're printing

    Dark prints are usually too much ink for that fabric, not a printer fault. In Garment Creator 2, open Print Settings, pick the T-shirt type that matches your garment, and click Print Chart under Ink Density. Print the chart on the same kind of shirt you'll use, pre-treated and on the same platen, and cure it. On a dark shirt chart, pick the one block with the best color without bleeding. On a light shirt chart, check bleeding in the top half and color density in the bottom half. Enter that block's value in Color Density (use White (Top) only if pure white areas need to be denser or the white bleeds into other colors), and register the result in your Presets. Epson recommends redoing this whenever you change fabric or shirt brand.

  7. Fix head height and under-base spread

    If the head is too far from the shirt, Epson says you get banding, blurry edges, doubled lines and grain. Check the spacers and platen height suit the garment. If white shows past the design edges, raise Reduce White Area in Garment Creator 2. On polyester with white, set print quality to the highest level.

Remember that monitors and printers make color differently. Judge color on a cured print, not a wet one, and compare it with the ink density chart rather than the screen.

Still thin or still dark? Text us a photo of the print and your nozzle check at (562) 609-4996.

Epson's video: printing the density test chart on the F2270

More videos

Epson: printing a nozzle check on the F2270
Epson: shaking the F2270 ink packs
Epson: printing on a dark garment with the F2270

Embedded from the manufacturer's official channel.

Common questions

Is weak white a printer fault?

Usually not. Epson's own list starts with shaking the White ink, pre-treatment, drying and heat press pressure before it gets to cleaning.

How do I make prints less dark?

Print the Ink Density chart in Garment Creator 2 on the same shirt you're printing, cure it, pick the best block and enter its value in Color Density. Save it to your Presets.

What do I need for the Color ink mode round trip?

Two Cleaning Liquid packs to switch to Color ink mode and two White ink packs to switch back. Have new color packs ready if any are low.

Can I change mode if I set up in High speed color mode?

No. Epson says the printer mode can't be changed if High speed color mode was chosen during initial setup.

White looks fine on the shirt but spreads past the edges of the design.

Increase Reduce White Area in Garment Creator 2 so the automatic under-base stays inside the image.

Did this fix it?