Support
Machine type
Brand
Epson SureColor F570

Epson F570 loading roll paper and cut sheets, paper type settings, and clearing paper jams

✓ Reviewed by Jason KimUpdated 3 min readFits: F570 · SC-F500
Short answer

On the F570, cut the roll's end straight, fit it on the spindle with both paper stops tight against the roll, set it in the holders with the black end of the spindle on the right, and feed the edge in until it beeps. Then choose the paper type on the screen: for Epson DS Transfer Multi Use, General Purpose/Textile or General Purpose/Rigid. For a jam, cut the paper above the feed slot, pull it out the front, check under the front cover, restart and reload with a straight edge.

Keep the roll paper cover and cut sheet cover closed except when loading, so dust stays out. Remove paper when you finish printing; paper left in the printer can get dented or creased at the edge.

Loading roll paper

  1. Prepare the roll

    Remove tape and protective paper and make sure the end is cut straight across. Don't touch the print surface. Check the screen shows Load paper.

  2. Open up and take out the spindle

    Open the cut sheet cover, release the central lock and open the roll paper cover. Lift out the spindle and remove its transparent paper stop.

  3. Mount the roll

    Slide the spindle into the core with the leading edge facing you. Push the fixed stop against the roll with no gap, then refit the transparent stop and press it in until there's no gap on that side either.

  4. Set it in the printer

    Place the spindle in the holders with the black end on the right. Insert the leading edge into the paper feeder until you hear a beep. A bent or skewed edge causes jams and skew errors.

  5. Close and set the type

    Close the roll paper cover and the cut sheet cover. Choose the paper type on the screen and set the remaining amount if you want the printer to track it. If you have the optional stand, open the paper basket.

Loading cut sheets

  • One sheet at a time: remove any roll paper, close the auto sheet feeder and take off the output tray. Choose Paper Setting > Cut Sheet (1 sheet), open the cut sheet cover, and load the sheet printable side up, portrait, with the right edge on the right edge guide and the left edge on the size mark. Push it in until it beeps, then choose the type and size.
  • Auto sheet feeder: up to 50 sheets of plain paper, A3, A4, Letter or Legal. Attach the output tray, open the cut sheet cover, tilt the feeder back and raise the paper supports, slide the edge guides out, load printable side up in portrait, set the guides, and choose the type and size. A roll can stay loaded; switch source in the driver.

Choosing the paper type

Paper Paper Type setting
DS Transfer Multi Use, for fabric General Purpose/Textile
DS Transfer Multi Use, for hard items General Purpose/Rigid
Other paper Others, then your Custom Paper

To make a custom paper (up to 10), load the paper and go to Settings > General Settings > Printer Settings > Custom Paper Setting. Pick a number, use Change Name, then Change Reference Paper to pick the closest Epson type, and Advanced Media Setting for anything else. Choose it later from Paper Setting > Change Paper Type > Paper Type > Others > Custom Paper.

Cutting and removing roll paper

With Auto Cut on, the printer cuts after each page. The driver setting overrides the panel. To cut by hand, turn Auto Cut off, then from the roll paper area choose Feed/Cut Paper, move the cut point to the dotted line with Forward or Backward, and choose Cut. The cutter can't cut pieces shorter than 100 mm. To unload, open both covers, choose Remove, wait for a full rewind, lift out the spindle, and store the roll in its box, on its end or flat with the end caps on, never on its edge.

Clearing a jam

  1. Roll paper

    Open the cut sheet cover and the roll paper cover. Cut the paper above the feed slot. Close both covers and pull the jammed paper out the front.

  2. Check inside

    Open the front cover and remove any other pieces. Don't touch the print head. Close the cover.

  3. Restart and reload

    Turn the printer off and on. Cut the roll edge straight, removing any jagged or folded part, and reload. For a cut sheet jam, pull it out the front, check under the front cover, restart and load a new sheet.

If paper won't feed: load sheets short edge first, use flat paper that isn't damp or curled, close any gaps at the paper stops, and match the driver's media type to the paper. If ink smears on prints, choose Paper Setting > Roll Paper > Feed/Cut Paper and hold Forward until the paper comes out clean, then cut.

Watch Epson's video: loading media in the SureColor F570 (SC-F500)

Embedded from the manufacturer's official channel.

Common questions

Will a 3 inch core roll fit?

No. Epson says the F570 doesn't support 3 inch core media.

Which paper type do I choose?

For Epson DS Transfer Multi Use, choose General Purpose/Textile for fabric or General Purpose/Rigid for hard items. For other papers, make a custom paper configuration based on a similar Epson type.

Why do I get skew errors?

Usually a bent or crooked leading edge, or gaps between the roll and the paper stops. Cut the end straight and push both stops tight against the roll.

How many sheets does the auto sheet feeder take?

Up to 50 sheets of plain paper in A3, A4, Letter or Legal. Load one sheet at a time through the cut sheet slot for other sizes up to 24 inches wide.

My roll is wrinkling as it prints.

Epson says adjust the Back Tension setting.

Sources
Did this fix it?