Support
Machine type
Brand
Epson SureColor G6070 DTF printer

Epson G6070 error messages: what they mean, printer error codes, maintenance requests and ink leak warnings

✓ Reviewed by Jason KimUpdated 3 min readFits: G6070
Short answer

Most G6070 messages tell you to do something specific: shake ink, clean the suction cap, replace a part or fix the network. For a "Printer error" with a code, Epson says turn the printer off, unplug the cable at both the outlet and the printer, reconnect and turn it on. If the same code returns after several tries, write it down and contact us or Epson. If the screen warns of an ink leak or tells you not to move the printer, leave it where it is and call for service.

Common messages

Message What to do
Failed to inspect nozzles / Cannot run Auto Cleaning The room is outside the printer's guaranteed temperature (50 to 95°F). Fix the room, then run Head Cleaning manually at a strength you choose.
Ink shaking is needed Take out and shake that pack. If the message has no Close button, the printer won't print until you do.
You need to replace Ink Supply Unit Replace it. With White, do it right away: Epson warns the head can be damaged if you ignore it.
It is time to clean the Suction Cap Clean it (see our G6070 maintenance guide). If it keeps appearing, contact us.
Auto Nozzle Maintenance found clogged nozzles exceeded Real clogs. See our G6070 clogged nozzles guide.
Waste Ink Bottle nearing or at end of life Get a new bottle, and replace it when told to.
Head Cleaning Set nearing end of its service life Order a set now. The printer stops printing until all its parts are replaced.
Replacing the auto cutter blade is recommended The blade is worn. Replace it.
Before storage, clean the ink supply port Touch a wide cleaning stick to the port of the pack you removed before storing it.
Network communication unstable Turn IEEE802.3az (Energy Efficient Ethernet) off. Steps below.
IP address and subnet mask combination invalid Re-enter the IP address and default gateway, or ask whoever manages your network.
Recovery Mode A firmware update failed. Connect by USB (network updates don't work in this mode), download the latest firmware from Epson and run the update again.
Media out Press How To... and follow the cutting steps, then load a new roll.

"Printer error" with a six-digit code

  1. Power cycle the right way

    Turn the printer off. Unplug the power cable from the wall outlet and from the printer's AC inlet, then plug both back in firmly and turn it on.

  2. Try a few times

    A loose power cable can cause this message. If the same code comes back after several tries, stop and write the code down.

  3. Contact us or Epson

    Give the code, the serial number and what was happening. Text us at (562) 609-4996.

Maintenance requests

"Maintenance Request: Replace Parts Soon" means a part is nearing the end of its life. "End Of Parts Service Life" can't be cleared until the part is replaced, and keeps leading to a printer error if you carry on. Note the code and contact us. The printer's Replacement Part Information menu lists service parts such as the ink damper, ink holders, pump cap, air unit, ink tube, circulation pump and capping station unit, and Epson says to contact your dealer or Epson about those.

Ink leak or ink path warnings

If the screen reports an ink leak or ink path problem, follow what it says. Don't move or tilt the printer and don't take it apart. Keep the waste ink bottle installed, even with the power off: Epson warns that ink in the waste tubes can leak out. Write down the code and contact us or Epson for service.

Turning off IEEE802.3az

  1. Connect directly

    Unplug the network cables from the computer and printer. If the computer has IEEE802.3az on, turn it off. Connect the computer and printer with one network cable.

  2. Open Web Config

    Find the printer's IP address under Menu > General Settings > Network Settings > Advanced > TCP/IP, type it into a browser, and log in as administrator.

  3. Switch it off

    Go to Network Settings > Wired LAN, set IEEE 802.3az to Off, click Next, then OK. Reconnect your normal cables and turn the computer setting back on if you changed it.

Watch Epson's video: checking the temperature and humidity inside the G6070

More videos

Epson: how to print a network status sheet
Epson: how to find the IP address of the printer

Embedded from the manufacturer's official channel.

Common questions

Where do I see every warning, not just the last one?

Press the printer status area on the home screen, then Message List. Each item shows details and the fix.

What does the alert lamp mean?

It lights or flashes when there's an error. Check the screen for which one.

What do I tell support?

The full code on the screen, your printer's serial number, and what you were doing when it appeared. Epson's warranty service asks for the serial number, the printer's address, the purchase date and the problem.

Is my G6070 under warranty?

Epson's limited warranty runs one year from purchase or 5,150,000 carriage passes, whichever comes first, in the US, Canada and Puerto Rico. It doesn't cover damage from non-Epson ink.

The screen says "Motor self adjustment running." Is it stuck?

No. The printer is adjusting a motor. Wait, and don't turn it off.

Did this fix it?