Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson G6070 powder and curing workflow: running an inline shaker the way Epson describes
The G6070 has no curing unit: you apply powder and heat with an inline shaker, or by hand with a tray and an oven, then transfer with a heat press, peel, and press again under silicone paper. Line the shaker up with the right edge of the film, keep powder away from the printer, never rewind powdered film, and turn the shaker heater off if the printer stops mid-run. Epson doesn't publish temperatures: use your powder, film and shaker maker's settings.
Epson's finishing order
-
Apply powder and heat
Either feed the printed film straight into a powder shaker and dryer, or lay it in a tray, apply powder by hand and cure it in an oven. Do it before the ink dries, and don't stack or fold the film.
-
Transfer
Use a heat press to transfer the image from the film to the garment, then peel the film.
-
Fix
Lay silicone paper over the design and press again to fix the ink.
Epson leaves temperatures, times and pressure to your powder, film and equipment makers. Start there, then test on the garments you actually sell.
Running the G6070 with an inline shaker
- Line it up. Set the shaker up using the edge of the film as the guide. Epson marks the right edge of the media on the printer so you can line the two machines up.
- Leave room on the left. You need space on the printer's left side to swap ink packs during a run.
- Keep powder out of the printer. Powder that gets inside can cause malfunctions, clog the head or scratch the film. Don't let it scatter around the printer, and never rewind powdered film back into it.
- If the printer stops, turn the shaker heater off. Epson recommends switching the heater off temporarily when printing stops for any reason, to avoid overheating.
- Cutting. Use the printer's manual cut or sheet cut when you need to separate a run. The minimum cut length is 100 mm (3.94 in).
Changing an ink pack mid-run
When a pack runs out during a run, printing pauses. If your shaker lets the film hang slack between the two machines, take up the slack first so the swap is easier:
-
Make sure printing has stopped
Wait for the pause before touching anything.
-
Take up the slack
Run the shaker manually until the slack is gone. Don't pull the film tight: too much tension can affect print quality.
-
Swap the pack
Reach under the film without touching it, and follow How To... on the screen to replace the pack. Shake the new pack in its tray first.
-
Resume
Set the shaker back to auto and resume printing.
Colors can look slightly different on either side of a mid-run swap, depending on how the ink dries. Epson suggests replacing a low pack before a long run starts.
Epson warns that powder inside the printer can cause malfunctions, head clogs and scratched film. Clean up spills around the printer right away.
Watch Epson's video: replacing G6070 ink packs
More videos
Embedded from the manufacturer's official channel.
Common questions
What curing temperature and time should I use?
Epson's G6070 manual doesn't give any. Start with your powder and film maker's settings and your shaker's recommended values, then test. Our DTF powder curing guide has starting points.
Can I finish G6070 prints without a shaker?
Yes. Epson describes laying the printed film in a tray, applying powder by hand, and curing it in an oven.
Why turn the shaker heater off when the printer stops?
Epson warns the shaker's heater can overheat the film and printer area if the line stops mid-run.
Can I let printed film sit before powdering?
Epson says to post-process before the ink dries, and not to stack or fold printed film.
I get specks of melted powder and pinholes in the print. What's wrong?
That's a powder and film issue, not the printer. See our guide on DTF powder sticking to bare film, and text us a photo at (562) 609-4996.
- Epson SureColor G6070 (SC-G6000 Series) User's Guide
- Epson SureColor G6070 Setup Guide
- AA support requests about G6070 with Miro and Seismo shakers, powder and curing, 2024 to 2026











































































