Support
Machine type
Brand
Epson SureColor G6070 DTF printer

Epson G6070 replacing ink packs, the waste ink bottle, the head cleaning set and the cutter blade

✓ Reviewed by Jason KimUpdated 2 min readFits: G6070
Short answer

Replace each G6070 consumable when the printer asks, and always start the job from the Maintenance menu or the on-screen message so the printer resets its counter. Ink packs: unlock the tray, follow How To..., and shake the new pack. Waste ink bottle: keep it installed at all times. Head cleaning set: replace all three parts together, or the printer won't print. Cutter blade: replace it when cuts are ragged.

When to replace what

Part When
Ink pack When the screen says to replace it. White right away.
Waste ink bottle When the screen says it's at the end of its life, or early from the menu
Head cleaning set When the screen says it's near the end of its life
Cutter blade When cuts are ragged or frayed, or the screen recommends it

Wear the gloves from the maintenance kit, plus glasses and a mask. Use genuine Epson parts. Epson says damage from non-Epson ink isn't covered by its warranty.

Step by step

  1. Ink packs

    When the replace message appears, press How To... and follow along. Slide the lock switch for that color to the right to unlock the tray, and support the tray from underneath as you pull it out. Shake the new pack in the tray at about 60 degrees: about 25 times in 25 seconds for White, 15 times in 15 seconds for the colors. Slide the tray in and move the lock switch back to the left. Every tray must hold a pack or the printer won't print. Epson notes the built-in cutter may not work right after some ink swaps. If so, cut the film with scissors.

  2. Waste ink bottle

    When the screen says the bottle is at the end of its life, replace it right away using How To.... To replace it early, for example before a long overnight run, go to Maintenance > Replace Maintenance Parts > Waste Ink Bottle so the waste ink counter resets. Never pull the bottle during printing, head cleaning or Keeping Preparation. Make sure the waste tube sits in the bottle's mouth, keep the bottle's lid to seal it, and dispose of the ink in the bottle. If you must pour waste ink out, use a polyethylene container and the spout supplied with the printer, and pour slowly.

  3. Head cleaning set

    The set holds a wiper unit, a capping station and a flushing pad. Replace all three. When the near-end message appears, press OK; otherwise go to Maintenance > Replace Maintenance Parts > Head Cleaning Set, press Start and follow How To.... Lift the old flushing pad gently or waste ink can spray. Afterward, check the new flushing pad's hooks are fully seated: raised hooks can damage the head.

  4. Auto cutter blade

    Have a Phillips screwdriver ready. Go to Maintenance > Replace Auto cutter blade, press Start and follow How To.... Leave the protective sheet on the new blade: it comes off by itself when the blade returns to position. Tighten the screw firmly, or cuts can drift or angle. Put the old blade in a bag before you throw it away.

Throwing used parts away

Epson classes used ink packs, waste ink, the waste bottle, wiper unit, capping station, flushing pad, cleaning sticks and ink cleaner as industrial waste. Follow your local rules. A disposal company may ask for Epson's Safety Data Sheet, which is on Epson's website.

The buzzer sounds 10 minutes after the head moves out for a replacement, and again every 10 minutes. Work steadily so the head isn't left uncapped.

Watch Epson's video: replacing G6070 ink packs

More videos

Epson: how to replace the waste ink bottle
Epson: how to replace the head cleaning set
Epson: how to replace the auto cutter blade

Embedded from the manufacturer's official channel.

Common questions

Which part numbers does the G6070 use?

Ink packs T57S series (UltraChrome DF, 1.6 liters), waste ink bottle T7240, head cleaning set C13S400262, maintenance kit T7362, auto cutter spare blade C13S902006 and Cleaning Ink Supply Unit C13T57Y100. The current part number for each item also shows on the printer's Supply Status screen.

How big is the waste ink bottle?

2 liters. The printer warns you before it's full.

Can I run the printer without the waste ink bottle?

No. Epson says it must be installed at all times, even when the printer is off.

Can I put a half-used ink pack back in later?

Yes. The chip remembers how much is left. Clean the port with a wide cleaning stick before storing it, and store it flat.

Why does the printer say a pack is empty when there's still ink inside?

Epson designs the printer to stop before the pack is completely empty, to protect the print head.

Did this fix it?