Support
Machine type
Brand
Epson SureColor G6070 DTF printer

Epson G6070 setup and first print: stand, ink charging, software and media settings

✓ Reviewed by Jason KimUpdated 3 min readFits: G6070
Short answer

Set the G6070 up where it can stay: a flat floor, a grounded outlet and 68 to 77°F. Assemble the stand with three people, then turn the printer on and let it walk you through initial ink charging without touching anything else. Install Epson's communications driver and a RIP on a Windows computer, load film, pick the media setting, and run a nozzle check, Print Head Alignment and Media Feed Adjustment before your first real job.

Before you start

  • A place that suits it. Flat and solid enough for 285 lb plus ink and film, low dust, out of direct sun and away from heaters and air-conditioning drafts. Epson recommends 68 to 77°F and 40 to 60% humidity.
  • Power. A grounded outlet that meets the printer's rating. Plug in directly, never through a power strip, and use the power cable that came with the printer.
  • Ink. A full set of UltraChrome DF packs. They are sold separately, and the first charge uses a lot of ink.
  • Room for the shaker. If you run an inline shaker, leave working space on the printer's left side so you can change ink packs during a run.
  • A Windows computer for the RIP, connected by USB or a shielded Category 5e or better network cable.

Step by step

  1. Assemble the stand and mount the printer

    Follow the Setup Guide in the box. Epson recommends three people for the stand. Once the printer is in place, lock the casters. One of the small parts in the box is a spare and will be left over.

  2. Turn it on and run initial ink charging

    Choose the language and date, then follow the screen. Have the ink charging unit and one of the supplied gloves ready. While it charges, don't unplug it, turn it off, open any cover, move a lock switch or press anything the screen doesn't ask for. Epson warns that an interruption can mean starting over and using extra ink. Shake each pack in its tray before it goes in, as the screen shows. Throw the ink charging unit away afterward as industrial waste.

  3. Connect it to the computer

    Use USB or wired network. For network use, find the printer's IP address under Menu > General Settings > Network Settings > Advanced > TCP/IP, or print a status sheet from Network Settings > Network Status > Print Status Sheet.

  4. Install the Epson software

    Download the software for your model from Epson's support page and run it. Install the Epson communications driver first, then Epson Edge Dashboard. When the installer asks for the administrator password, use the one on the label on the left side under the printer cover. If the printer is on your network, change it afterward and keep a record of it.

  5. Install and activate your RIP

    Epson includes Epson Edge Print PRO (install it from the URL on the sheet in its package) and Fiery Digital Factory Epson Production Edition. Both are full versions that need activation. Epson says the licenses can't be replaced, so store them somewhere safe. Our G6070 RIP setup guide covers EMX files and syncing print modes.

  6. Register a media setting

    The printer has two built-in media types, Film and Paper/Others. For better results, download the Epson EMX file for your film through Edge Print PRO or Edge Dashboard, which saves the settings to one of the printer's ten media numbers.

  7. Load film and pick the media number

    Press the load media icon on the home screen, then Start and See Description to follow the loading steps on screen. Select the media number that matches the roll, or the Film media type.

  8. Check and adjust before the first job

    Print a nozzle check and clean if there are gaps. Then run Media Settings > Print Adjustments > Print Head Alignment and Media Feed Adjustment with the film loaded the way you will print. Epson says to do both, once per media setting. When the screen says Ready to print, send your first job from the RIP.

Never pull the plug or switch off the breaker while the printer is on. The head may not cap and can dry out. If that happens, turn it back on and wait until it caps itself.

Stuck at any step? Text us a photo of the screen at (562) 609-4996.

Watch Epson's video: unboxing and setting up the G6070

More videos

Epson: how to load a roll of film
Epson: how to perform a print head alignment
Epson: how to find the IP address of the printer

Embedded from the manufacturer's official channel.

Common questions

Can I set the G6070 up myself?

Yes. Epson says owners can install it with the instructions in the box, and there is an unboxing and setup video on Epson's support page. Epson recommends three people to assemble the stand.

Is ink included?

No. Epson's setup guide says ink packs are sold separately and must be on hand before initial ink charging. The first charge uses a lot of ink to fill the head, so have spares ready.

Is there a printer driver for Mac or Windows?

No. The G6070 prints through a RIP. Epson Edge Print PRO runs on Windows only. Fiery Digital Factory Epson Production Edition is also included.

What is the administrator password?

It is on a label on the left side under the printer cover. With one label, it is the serial number. With two labels, it is the number on the PASSWORD label. Epson recommends changing it if the printer is on a network.

Do I need to adjust anything before printing on new film?

Yes. Epson says to run Print Head Alignment and Media Feed Adjustment once for each new media setting, with the film loaded the way you will print.

Did this fix it?