Support
Machine type
Brand
Epson SureColor S-Series (S40600, S60600, S80600)

Epson S40600, S60600 and S80600 clogged nozzles and banding: nozzle check, cleaning levels and feed adjustment

✓ Reviewed by Jason KimUpdated 2 min readFits: S40600 · S60600 · S60600L · S80600 · S80600L
Short answer

Print a nozzle check from the maintenance button. If lines are missing, run Cleaning (Light), check again, then Medium, then Heavy. If nozzles stay clogged, Epson's next steps are Auto Head Maintenance, then a regular cleaning around the head and caps, then Head Washing with cleaning cartridges. Banding with a clean nozzle check is usually media feed: run Feed Adjustment for that media.

Match your symptom

What you see Start with
Missing or faint lines in the nozzle check Head cleaning, Light first
Clean nozzle check but stripes in prints Feed Adjustment
Blurry or grainy prints Media settings: drying time, suction
Uneven tint with White or Silver (S80600) Shake ink, run Ink Circulation

Print a nozzle check

  1. Open the menu

    With media loaded, press the maintenance button and choose Nozzle Check, then the position: Print At Right, Center or Left.

  2. Read the pattern

    Unbroken lines mean the head is clean. Gaps or faint lines mean those nozzle rows need cleaning. Note which rows, and on two-head models, which head.

Epson recommends a nozzle check before each print job. You can also set Btw Pages Nozzle Check in the Printer Setup menu. Its Auto Nozzle Check option reads the pattern with a sensor and cleans automatically, but it isn't available with White or Metallic Silver, transparent media, a 2.5 platen gap, or strong light on the printer.

Clean the print head, in Epson's order

  1. Cleaning (Light)

    Press the maintenance button, choose Cleaning > Cleaning (Light) and run it on all nozzles. Print another nozzle check.

  2. Cleaning (Medium), then (Heavy)

    If gaps remain, run Cleaning (Medium), and if they still remain, Cleaning (Heavy). At these levels you can pick All Nozzles, one head (Head1 or Head2 on the S60600 and S80600), or Selected Nozzles for only the rows with gaps, then Execute With Selection. Check again after each one.

  3. Auto Head Maintenance

    If repeated cleanings don't clear it, the area around the head may be dirty. Run Head Maintenance > Auto Head Maintenance.

  4. Regular cleaning by hand

    Still clogged? Clean around the print head, the anti-drying caps and the flushing pad as described in our regular cleaning guide.

  5. Head Washing

    As a last owner step, Other maintenance > Head Washing flushes the head with cleaning cartridges (cleaning ink supply units on the L models), sold separately.

If nozzles are still missing after Head Washing, stop running cleanings, which only fill the waste bottle. Text us a photo of your latest nozzle check at (562) 609-4996.

Fix banding when the nozzles are clean

  • During a print: press the media setup button. Press up if you see dark bands (feed more), down for light bands (feed less), and repeat until they go.
  • For good: run Media Setup > Customize Settings > Media Adjust. Auto is available for adhesive vinyl and banner. For film, canvas, textile or paper, choose Manual, then Feed Adjustment and Head Alignment. The 500mm Pattern is Epson's most accurate option; a different width of the same media may need its own values.
  • Check that the roll holders were pushed fully into the core and the media edge plates are centered on the edges. Both cause banding when wrong.
  • Set Head Movement to Printer Full Width for more even results, raise the after heater a little and let it warm up, and keep the front cover closed while printing.
  • Increase Drying Time Per Pass if prints are blurry, and lower Media Suction for thin media that feeds badly or prints grainy.

Prevent clogs when the printer is idle

Leave the printer on. If it has to be off, turn it on at least once every seven days. For longer breaks, run Pre-Storage Maint.: a month or more on the S40600 and S60600; on the S80600, a week or more for White and Metallic Silver and two weeks or more for all colors. On the S80600, switch to 9 Color mode if you won't use White or Silver for 20 days or more.

Watch Epson's video: regular cleaning on the S-Series

More videos

Epson: regular cleaning on the S40600

Embedded from the manufacturer's official channel.

Common questions

Should I run a heavy cleaning first to save time?

No. Epson says to start with Cleaning (Light) and only step up if a fresh nozzle check still shows gaps. Every cleaning uses ink.

One head is clogged on my S60600 or S80600. Can I keep printing?

Yes. Set Head Mode to Head1 or Head2 in the Printer Setup menu to print on the good head while you sort out the other. Three-layer printing needs both heads.

How do I stop clogs when the printer sits idle?

Leave it on so it maintains itself. If it will be off, turn it on at least once every seven days, or run Pre-Storage Maint. with cleaning cartridges.

I see dark or light stripes across the print. Is that a clog?

Print a nozzle check first. If it's clean, it's feed. Dark bands mean feed too short, light bands mean too long. You can nudge feed during printing with the media setup button.

Why are my S80600 colors uneven when I use White or Silver?

Those inks settle. Remove and shake the cartridge, reinstall it, and run Ink Circulation from the Maintenance menu several times.

Did this fix it?