Support
Machine type
Brand
Epson SureColor S-Series (S40600, S60600, S80600)

Epson S40600, S60600 and S80600 regular cleaning: print head, caps, flushing pad, wiper and waste ink bottle

✓ Reviewed by Jason KimUpdated 3 min readFits: S40600 · S60600 · S60600L · S80600 · S80600L
Short answer

Wipe the platen heater and media edge plates with a damp cloth every day. At least once a month, or when the screen says to perform Head Maintenance, run Regular Cleaning: the head moves out, and you clean around it and the anti-drying caps with ink cleaner on a fresh cleaning stick, then wipe the flushing pad. Replace the wiper unit, flushing pad and air filters together, and the waste ink bottle, when the printer asks.

What to clean and when

Part When Clean with
Platen heater, edge plates Every day before work Soft cloth dampened with water, wrung out
Around the print head At least monthly, or when prompted Ink cleaner on a new cleaning stick
Anti-drying caps At least monthly Ink cleaner on a new cleaning stick
Flushing pad Monthly or when dirty Tip of a cleaning stick, to lift lint

Epson says to clean more often if your room or media are dusty. Before you start, remove the media, touch something metal to discharge static, and wear the gloves from the maintenance kit plus eye protection and a mask. Use only the cleaning sticks supplied for the printer, never reuse a stick, and don't touch its tip.

Daily: platen heater and media edge plates

Turn the printer off, wait for the screen to go dark, unplug both power cables (and the drying system, if fitted), and wait one minute. The heaters may still be hot. Wipe the platen heater, the platen grooves and the edge plates with a well wrung-out damp cloth. If your media has glue on it, use a mild detergent solution instead. Don't use ink cleaner here.

Monthly: regular cleaning

  1. Move the head out

    Press the maintenance button and choose Head Maintenance > Regular Cleaning, then press OK again. Wait for the message that the head is in the maintenance position. An alarm sounds every 10 minutes while it's out; press OK to keep going.

  2. Pour a little ink cleaner

    Put the cup on the metal tray and pour in about 10 ml (0.3 oz). Recap the bottle. Use fresh cleaner and a fresh stick every time.

  3. Clean around the print head

    Open the left maintenance cover and wipe the areas around the head that Epson's video shows, with a new stick dampened in cleaner for each area. Lift any clots with a wipe. The S40600 has one head; the S60600 and S80600 have two. Close the cover.

  4. Clean the caps

    Open the right maintenance cover. Hold a damp stick flat on the top edge of each cap and wipe, then clean the outside. Don't press hard and don't touch the inside of the caps, or they may not seal the head. Remove any film of ink or lint with the tweezers.

  5. Wipe the flushing pad and finish

    Lift lint off the flushing pad with the tip of a stick. Close the cover and press OK.

Replace the maintenance parts

The maintenance parts kit holds one wiper unit, one flushing pad and two air filters, and they're replaced together. Start only from the replacement message or Maintenance > Replace Parts, otherwise the counter won't reset.

  1. Wiper unit

    Once the head moves left, open the right maintenance cover. Tilt the old wiper forward by the groove on its back, pull it straight out and wrap it in the new one's packaging. Press the new wiper down until it clicks.

  2. Flushing pad

    Lift the tab, remove the old pad and set it on the metal tray, not on the printer. Fit the new pad into its slots and press the tab down until it clicks. Press OK.

  3. Air filters

    Lift the old filters straight out, wrap them, and insert the new ones. Press OK, close the cover, press OK, then choose Yes.

Replace the waste ink bottle

Never swap it while printing or cleaning. Lift the full bottle out of its holder, cap it tightly, put the waste ink tube into the new bottle and set it in the holder. Press OK, then OK again to reset the counter. Keep the bottle in place any time the printer is on.

If you see Apply secondary carriage rod grease, use the grease kit that came with the printer and follow the steps in Epson's user's guide. If the screen shows a Maintenance Request or Call For Service code instead, note the code and contact us.

Watch Epson's video: regular cleaning on the S-Series

More videos

Epson: SureColor S-Series maintenance overview
Epson: regular cleaning on the S40600

Embedded from the manufacturer's official channel.

Common questions

The screen says Press maintenance and perform Head Maintenance. What does that mean?

Regular cleaning hasn't been done for more than a month. Epson warns that skipping it can cause ink drops, clogged nozzles or head damage. Run Regular Cleaning as soon as you can.

Can I use alcohol or water on the caps or wiper?

No. Epson says not to use alcohol or water on the nozzle surface, caps or wiper. Use the ink cleaner, and only around the print head and caps.

Can I push the print head over by hand to clean?

No. Always move it with Maintenance > Head Maintenance > Regular Cleaning. Moving it by hand can cause a malfunction.

Can I replace just the wiper?

Epson says to replace all the maintenance parts (wiper unit, flushing pad and air filters) at the same time, and to start from the on-screen message or Replace Parts so the counter resets.

Can I pour waste ink into another container?

No. Leave it in the bottle, cap it tightly, and dispose of it as industrial waste under local rules.

Did this fix it?