Support
Machine type
Brand
Epson SureColor S-Series (S40600, S60600, S80600)

Epson S40600, S60600 and S80600 ink cartridge not recognized, ink supply unit errors and other screen messages

✓ Reviewed by Jason KimUpdated 2 min readFits: S40600 · S60600 · S60600L · S80600 · S80600L
Short answer

An S-Series printer only prints when every slot (or every tray on the L models) holds an ink cartridge or ink supply unit and every lock lever is down. For Ink Cartridge Error, take the cartridge out and put it back. If the error stays, fit a new one. A cartridge that came from a cold room needs at least four hours at room temperature first. If every slot errors at once and reseating doesn't clear it, contact us.

Match your symptom

What you see Likely cause Go to
Ink Cartridge Error, cannot be recognized or detected Cartridge not seated, cold, or faulty Reseat, then replace
All ink lights on, asks to install and lock Slots empty or lock levers up Check every slot
Ink Supply Unit Error (L models) Unit or tray not seated, or faulty unit Reseat the tray
Replace cleaning cartridge Cleaning cartridge not read Reseat, then replace

Fix an ink cartridge that isn't recognized

  1. Check every slot

    Every slot must hold a cartridge, matched to the label on the printer, with its lock lever lowered. The screen shows separate icons for a cartridge that isn't latched and a slot that's empty.

  2. Reseat the cartridge

    With the printer on, lift the lock lever, pull the cartridge straight out, push it back in and lower the lever. Don't touch the green chip. Watch for ink around the supply port.

  3. Let a cold cartridge warm up

    Epson says condensation can form inside a cartridge stored cold. Leave it at room temperature for at least four hours before installing it.

  4. Try a new cartridge

    If the error comes back, install a new genuine cartridge. Epson's guide says not to reinstall the cartridge that caused the error. Epson can't guarantee non-genuine ink, and damage from it may not be covered by Epson's warranty.

  5. If every slot errors at once

    When all the cartridges are rejected together after reseating, it's unlikely they all failed at once. Turn the printer off and on, and if nothing changes, text us a photo of the screen at (562) 609-4996.

L models: ink supply unit errors

On the S60600L and S80600L, ink comes from ink supply units in trays inside a separate ink unit. For Ink Supply Unit Error, pull out the tray and reinsert the unit. If the message stays with the tray in place, replace the unit. Every tray must hold a unit and be locked in (lock switch to the left), or nothing prints. Hold the bottom of the tray when you pull it out; it's heavy.

Tray light Meaning
Lit blue Supplying ink. Don't pull the tray
Flashing blue Time to shake this unit
Orange Error or warning; read the printer screen
Off No error; the tray can be pulled

Shaking and handling ink

  • Shake installed cartridges every three weeks: hold level, about 15 times in 5 seconds.
  • S80600 White and Metallic Silver: shake every day, and replace them right away when expended, or the head can be damaged.
  • L models: shake units in the tray by tilting about 60 degrees, about 5 times in 5 seconds. New Orange, White and Metallic Silver units get about 25 times in 25 seconds.
  • Use ink within 6 months of installing it, and before the date on the package.
  • Never leave slots empty, even when the printer is idle. Ink in the printer can dry out.

Other common messages

Message What to do
Prepare empty waste ink bottle Have a new bottle ready; it's almost full
Command Error Cancel the job and check your RIP supports this printer
Media Size Error Media must be at least 11.8 in (300 mm) wide. If it is, turn off Media Size Check
Roll Type Error Raise and lower the loading lever, then set the roll type to match
F/W Install Error Turn off, wait a few minutes, turn on, and update the firmware again
Maintenance Request A part is near or at end of life. Note the code and contact us
Print head nearing end of life Contact us

Common questions

All the ink lights are on and the screen asks me to install ink and lock it. Why?

The printer sees the slots as empty or unlatched. Check that every slot has a genuine cartridge pushed all the way in and that each lock lever is lowered. The printer can't print with any slot empty or any cartridge expended.

Can I put back a half-used cartridge?

Yes. The chip remembers the ink level. Wipe ink off the supply port with a cleaning stick first, because dried ink there can make it leak.

How often do I shake the ink?

Every three weeks for most colors, and daily for White and Metallic Silver on the S80600. A new cartridge gets about 15 shakes in 5 seconds; Orange, White and Metallic Silver get about 50 in 15 seconds.

The tray light on my L model is flashing blue. Is that an error?

No. It means that ink supply unit is due to be shaken. Pull the tray out and shake it.

What is Call For Service?

An error the printer can't clear itself. Turn it off, unplug it from the wall and the printer, reconnect, and turn it on. If the same code returns, note it and contact us.

Sources
Did this fix it?