Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Geo Knight DK7 cap press and DK8 label press: setup, cap hold-down, forms, tables and lining up the pedestal
On the DK7 cap press, pull the back strap of the cap behind the pedestal and under the half-moon hold-down so the front stretches over the curved form, and use the Euro form if low-profile caps wrinkle in the middle. If the heat platen doesn't land squarely on the table, loosen the gibb plate screws, slide or turn the pedestal into line and tighten them again. Pressure is set by feel with the knob, since these models don't use the bar graph.
The DK7 (4 x 7 in curved cap press) and DK8 (6 x 8 in label press) share one Geo Knight manual, one controller and the same frame. The twin DK7T and DK8T have two lower stations. Temperature, time, prepress and presets work exactly like the bigger clamshells: see DK clamshell setup, temperature, timer and presets.
Set up
- Use a firm bench about 27 to 32 in high and bolt the base through its front and rear mounting holes so the press can't hop when it opens.
- Plug the cord into the inlet on the back of the control box, with no strain on the socket.
- Leave the head up while heating and when idle.
Set pressure
Turn the knob counterclockwise to increase pressure (the head comes down) and clockwise to decrease it. The press must lock with a firm "ka-thunk" when you close it, not just rest on the item. There is no bar graph on these models, so judge by the lock.
Turn the knob in small steps. If you unscrew it too far, the heat platen can come off the frame and drop onto the table.
Load a cap on the DK7
-
Pick the form
Use the Standard curved form for most caps. If you see wrinkling or folding in the middle of the cap, Geo Knight says the form is wrong for that cap. The Euro mid-sized form is the fix for low-profile, tight-fitting caps.
-
Stretch it with the hold-down
Pull the cap over the curved form, then take the back strap behind the pedestal and tuck it under the half-moon hold-down bracket. That keeps the front panel tight for pressing.
-
Check alignment
The curved heat platen should come down centred on the form. If it doesn't, adjust the pedestal (below).
Change tables on the DK8
The tables sit on the pedestal over two bullet-shaped steel pins. Lift one off and drop the next one on. The DK8 comes with 6 x 8, 3 x 5 and 3 x 3 in tables. Geo Knight also makes custom tables and tongue-style pedestals supported from the rear, which help when loading pockets and bags.
Line up the pedestal
-
Slide it
If the platen lands too far forward or back, loosen the screw in the gibb plates that hold the pedestal, slide the pedestal along the base and tighten again.
-
Square it
If the table is twisted relative to the platen, loosen all four gibb plate screws, turn the pedestal until it lines up, and retighten.
-
Test
Close the press on a sheet of paper and look at the impression. It should be even all the way round.
Bottom heat
For thick embroidered appliques and other jobs that scorch from the top, Geo Knight makes separately controlled bottom heat fixtures that drop into the table position: a 3 x 5 in curved fixture for cap presses and a 6 x 8 in fixture for the DK8.
For timer, keypad, gas spring or power faults, see DK clamshell troubleshooting, or Text us a photo or short video at (562) 609-4996.
Common questions
Why don't I see a pressure number on my DK8?
The DK7, DK8 and twin models don't use the pressure bar graph. Set the knob so the press locks with a firm clamp.
Which forms come with the DK7?
Geo Knight lists the Standard and Euro mid-sized forms. A youth form and a bottom heat fixture are optional.
The tables are hard to pull off the pedestal.
The two steel locating pins can be tight from the factory. Geo Knight says the holes in the tables can be reamed out a little for a looser, faster change.
Which tables come with the DK8?
6 x 8, 3 x 5 and 3 x 3 in. The twin DK8T includes two sets.
- Geo Knight DK7, DK8 and Twin Digital Clamshell manual
- Geo Knight 2026 catalog
- AA support requests about Geo Knight presses, 2024 to 2026











































































