Support
Machine type
Brand
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap

Geo Knight DK20, DK16 and DKA clamshell setup: bench, temperature, timer, prepress and presets

✓ Reviewed by Jason KimUpdated 3 min readFits: DK20 · DK16 · DKA Auto Clamshell (DK20A, DK16A)
Short answer

Bolt the clamshell to a firm bench 27 to 32 in high, plug the cord into the inlet at the back of the control box, and leave the press open while it heats. Press TEMP, set the temperature with the arrows and press TEMP again. Set the time with the arrow keys only. Press PRG to load one of 70 presets, and remember that a preset reminds you of the pressure but doesn't set it.

These steps follow Geo Knight's DK16 and DK20 clamshell manual. The DKA auto clamshell uses the same manual and controller. For pressure, the bar graph and the auto-release pop-up, see DK clamshell pressure, auto-release and linkage.

Set up the press

  1. Pick the bench

    Use a firm, sturdy surface about 27 to 32 in high. A higher bench makes the press harder to close and lock. Geo Knight also sells a stand with locking casters.

  2. Bolt it down

    Geo Knight recommends bolting the base frame to the bench through the front and rear mounting holes. Clamshells can hop when they open fast, and the auto-release makes that more likely. Bolting stops your shirt from shifting on the table.

  3. Connect power

    Plug the power cord into the inlet on the back panel of the control box. Route it so nothing can pull on it and there is no strain on the inlet socket.

  4. Leave it open

    Keep the head up and unclamped while the press heats and whenever it is idle. Only close it on the pad for transport.

Read the screen

In normal mode the top number is the actual platen temperature and the lower number is the time. The right side shows HEATING or READY, and OPEN, TIMING or DONE. On the DK20 and DK16 the bar graph at the bottom shows the last pressure measured when the press was closed.

Set temperature and time

  1. Temperature

    Press TEMP. The flashing number is the setting. Use the arrows to change it (hold for fast, press both for 350°F), then press TEMP again to lock it in.

  2. Time

    Use only the arrow keys. Don't touch PRG. Hold an arrow for more than 2 seconds to scroll fast. Press both arrows to reset to 00.

  3. Prepress timer (optional)

    Turn it on in the user menus (press TEMP and PRG together, then PRG until PPR shows, and set it ON). When PREPRESS shows next to the time, the arrows set the prepress time. The first close runs the prepress time, and after you open the press it switches to the main time. If PREPRESS isn't showing, quickly close and open the press.

Save and load presets

There are 70 presets. Each holds a temperature, time, prepress time and a pressure reminder.

  1. Load

    Press PRG (SET shows), pick a number with the arrows, and press PRG again. The temperature and times change, and the screen briefly shows the saved pressure so you can set the knob to match.

  2. Edit

    Press PRG, pick the preset, then press TEMP to step through temperature, time, prepress time and pressure, using the arrows on each. Set prepress to 00 if that job uses one timer. After the pressure value, press TEMP and then PRG to leave.

The rest of the user menus (°F or °C, counters, temperature drop alarms, beeps) work the same as on the DK20S. See Digital Knight presets and user menus.

Change the lower table

The lower table drops onto its support: the angle brackets underneath slide along the sides of the square tubing, and the small bar strip sits inside it. If your press has a quick release pin, use it to lock the table so it doesn't lift from suction when the press opens. Smaller drop-on tables and bottom heat fixtures fit the same support.

Good pressing habits

  • Press shirts for 2 to 4 seconds first to remove wrinkles and moisture.
  • For a second side, pull the garment over the table so the printed side hangs underneath.
  • Keep collars, cuffs and zippers off the table. They spoil pressure and wear the pad.
  • Remove protective films from rigid blanks before heating, and check the transfer faces the item, not the platen.
  • Your transfer supplier's settings come first. Geo Knight's chart is a general reference only.

If something doesn't behave as described, Text us a photo or short video at (562) 609-4996.

Watch Geo Knight's video: Digital Knight control and instructions

More videos

Geo Knight DK20 clamshell heat press
Digital Knight heat press control system

Embedded from the manufacturer's official channel.

Common questions

What do HEATING and READY mean?

HEATING shows while the platen is still coming up to temperature. READY appears once the actual temperature is within 5 degrees of your setting.

Is the big number the setting or the real temperature?

In normal mode the top number is the actual temperature. When you press TEMP, the flashing number is the setting you are changing.

Does loading a preset change my pressure?

No. Pressure on a clamshell is set by hand with the knob. The preset briefly shows the pressure number you saved, as a reminder to adjust the knob until the bar graph matches.

How do I get back to 350°F quickly?

While the temperature is flashing, press both arrow keys together. It jumps to 350°F.

My lower table lifts when the press opens.

Fit the quick release pin if your press came with one. It locks the table to its support so suction doesn't pull it up.

Did this fix it?