Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Geo Knight DK20 and DKA clamshell: pressure knob, auto-release pop-up and loose linkage
On the Geo Knight DK clamshell, turning the pressure knob counterclockwise increases pressure and clockwise decreases it, the opposite of the DK20S swing-away. For the auto-release to hold, set firm but not heavy pressure and a timer of at least 5 seconds. If you keep turning the knob to get the same pressure, the 8 linkage bolts have loosened: tighten them, back them off half a turn, and lock them with threadlocker.
The DK20 (16 x 20 in) and DK16 (14 x 16 in) are Geo Knight's Digital Knight clamshells. The DKA auto clamshell is the same press with the Auto-Release pop-up fitted: an electromagnet holds the handle down while the timer counts, then gas springs lift the head. Everything here comes from Geo Knight's clamshell manual and support sheets.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Transfers peel, bar graph low even with the knob turned a long way | Knob turned the wrong way, or loose linkage | Setting pressure, then Loose linkage |
| Auto clamshell won't stay down, or pops up early | Pressure too heavy, timer under 5 s, or timer not counting | Using auto-release |
| Press jumps or the shirt shifts when it pops open | Press not bolted down | Set it up right |
| Head drops, knob runs out of thread, hover bracket comes loose | Worn or loose linkage | Loose linkage |
Set it up right
Put the press on a firm bench about 27 to 32 in high. Higher than that makes it hard to close and lock. Geo Knight recommends bolting the base to the bench through its front and rear mounting holes, because clamshells can hop when they open, especially with auto-release. Leave the press open when it's heating or idle. Don't let the heat platen rest on the pad.
Setting pressure
-
Know the direction
On the DK20 and DK16 clamshell, counterclockwise increases pressure and lowers the head, and clockwise decreases pressure. The DK20S swing-away works the other way, so don't go by habit.
-
Lock it, don't rest it
The press must lock in place with a firm clamp when you close it. A two-handed close with a solid clunk is what Geo Knight wants for good transfers.
-
Read the bar graph
The 0 to 9 bar graph updates only when the press is closed, locked and timing. Aim for 4 to 6 for most work. A thicker item raises the reading at the same knob setting.
Turning the knob too far counterclockwise can unscrew the heat platen from the frame and drop it onto the table. Go a little at a time.
Using auto-release
- Set pressure firm but not heavy. If it is too heavy, the electromagnet can't hold. The top bracket should flatten fully against the magnet.
- Set the timer to at least 5 seconds. At 00 the magnet won't engage.
- The magnet only works while the screen shows TIMING. Once DONE shows, it stays off until the press is fully opened and the timer resets.
- Turn on the Finished Warning Beep (FWB in the user menus) so you get a 3-second warning before it opens.
- For cure-only jobs, press the handle lightly so only the hover bar sticks to the magnet. That gives heat without pressure.
- To stop early, pull the handle firmly, or switch the press off and on quickly.
Loose linkage: the knob keeps needing more turns
-
Recognize it
You keep turning the knob further for the same pressure, the knob runs out of thread, the heat platen sags or drops from the frame, or the auto-release hover bracket comes off the blue handle.
-
Check the holes
Eight black Allen shoulder bolts hold the blue handle, side links and arm together. Remove the front four one at a time and look at the holes. They must be round. Worn bronze bushings or oval holes mean you need Geo Knight replacement hardware or a linkage kit, so send us a photo.
-
Tighten and lock
If the holes are round, tighten all 8 bolts very tight, then back each off half a turn so the linkage still pivots. Take the nuts off one at a time and put red threadlocker on them before refitting, so they don't loosen again.
-
Gain more thread (optional)
Under the black pressure knob, two locknuts sit around a black square block. Raise the top locknut as far as needed, then bring the bottom locknut back up against the block.
If the press still won't hold pressure, or you need gas springs, a pressure knob or linkage parts, Text us a photo or short video at (562) 609-4996 and tell us whether you have a DK16 or DK20.
Watch Geo Knight's video: DK clamshell auto pop-up pressure setting tutorial
More videos
Embedded from the manufacturer's official channel.
Common questions
Which way do I turn the knob for more pressure on a DK20 clamshell?
Counterclockwise (to the left). The head lowers toward the table. Clockwise raises the head and lowers pressure. Don't unscrew too far, or the heat platen can come off the frame and drop.
What bar graph number should I aim for?
Geo Knight says 4 to 6 is a good medium pressure for most work, 0 to 3 is light, and 7 to 9 is for demanding items. The press must still lock with a solid clamp.
My DKA won't stay down. Why?
Usually the pressure is too heavy for the magnet to hold, the timer is set to 00 or under 5 seconds, or the timer isn't counting. The magnet only works while the screen shows TIMING.
Can I add auto-release to my manual DK20 or DK16?
Geo Knight sells an Auto-Release Pop-Up upgrade for DK20 and DK16 clamshells with the newer Dual-Shock frame (the handle curves forward in front of the heat platen). Installing it involves wiring inside the control box, so ask us before you start.
The press opens weakly or won't stay open.
The gas springs lose force after many cycles. They are replaceable. When fitted, the silver rod faces down and the black tube faces up.
- Geo Knight DK20 and DK16 Digital Clamshell manual
- Geo Knight DKA Auto Clamshell manual (AA)
- Geo Knight Auto-Release Pop-Up instructions
- Geo Knight DK16 and DK20 clamshell linkage maintenance
- Geo Knight DK20S manual
- AA support requests about Geo Knight clamshell presses, 2024 to 2026











































































