Support
Machine type
Brand
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses

Air-powered heat press compressor setup: fittings, hose and psi (Maxima, Proxima, Hotronix Dual Air Fusion, Geo Knight DK20SP)

✓ Reviewed by Jason KimUpdated 2 min readFits: Maxima Auto Dual · Maxima Semi-Auto Dual · Proxima Auto · Proxima Semi-Auto · Hotronix Dual Air Fusion IQ · Geo Knight DK20SP
Short answer

An air press needs a compressor that can keep up, a dry air supply, and a fitting that matches your compressor's quick-connect. On the Maxima and Proxima, the press's thin air tube connects to a standard 1/4 in industrial quick-connect plug through a small 3/16 x 1/4 in hose-barb adapter sealed with PTFE tape. Set the Maxima to about 60 psi at the press with the compressor delivering 85 to 100 psi, and drain water from the filter and tank every day.

What each press needs

Press Compressor Pressure Connection
Maxima Auto and Semi-Auto Must deliver 85 to 100 psi About 60 psi on the press gauge Press tube to 1/4 in industrial quick-connect (adapter below)
Proxima Auto and Semi-Auto At least 1.5 kW, 50 L tank, 0.7 MPa Set with the press's pressure-reducing valve Air hose 5 mm ID x 8 mm OD, adapter below
Hotronix Dual Air Fusion IQ At least 8 gal and 3.8 CFM, continuous duty 110 to 120 psi delivered to the press See the Hotronix manual
Geo Knight DK20SP Standard shop compressor Set on the press regulator and gauge 1/4 or 3/8 in female NPT inlet, 1/4 or 3/8 in ID hose

Connect a Maxima or Proxima to your compressor

Many compressors, including the California Air Tools model we sell with the Maxima, have 1/4 in industrial female quick-connect outlets. The press's air tube needs a plug to match.

  1. Gather the parts

    You need a 1/4 x 1/4 in industrial quick-connect plug, a roll of PTFE thread seal tape, a 3/16 x 1/4 in hose-barb adapter, and optionally a small hose clamp.

  2. Tape the threads

    Wrap PTFE thread seal tape around the threads that join the adapter to the plug.

  3. Assemble the plug

    Thread the adapter into the industrial plug.

  4. Fit the press tube

    Push the press's air tube fully over the barb. Add the hose clamp over the tube if you have one.

  5. Connect and check for leaks

    With the compressor at pressure, click the plug into the compressor coupler. Check each joint for leaks before you start pressing.

Set the pressure and start up (Maxima)

  1. Open the air and set 60 psi

    Connect the compressor, open the air, and adjust the press gauge to about 60 psi. Lift the upper regulating valve and turn toward + to raise or - to lower.

  2. Power on and heat

    Switch on the main power, set time and temperature, and wait for the press to reach temperature before your first test.

  3. Test in manual mode first

    Place a garment, set the mode to manual, and press the start switch. After a good test you can leave it in automatic.

Water ruins air presses. Push the drain valve at the bottom of the press's air filter and drain the compressor tank every day. Keep a water trap in the line on presses that don't have one built in.

Still not connecting or not holding pressure? Text us a photo or short video at (562) 609-4996 of the press's air inlet and your compressor's outlet.

Common questions

The hose from the press doesn't fit my compressor. Is a part missing?

Usually not. The press tube needs an adapter to a standard 1/4 in industrial quick-connect. Our adapter sheet shows the exact pieces: a 1/4 x 1/4 in industrial plug, PTFE thread tape, a 3/16 x 1/4 in adapter, and an optional hose clamp.

What size compressor do I need?

Maxima and Proxima: Proxima manuals call for at least 1.5 kW with a 50 L tank and 0.7 MPa, and the Maxima manual wants 85 to 100 psi available. Hotronix Dual Air Fusion I

at least 8 gallons and 3.8 CFM, rated for continuous duty, delivering 110 to 120 psi.

Why do I need to drain the compressor every day?

Compressors make water. Hotronix and Geo Knight both warn that water and dirt in the air line damage the press's regulator, valves and air cylinder. Drain the tank and the press filter daily.

My Dual Air Fusion lost air with the platen down. How do I open it?

Hotronix says to turn the power off, remove the opposite lower platen, and push the top of the press to the open position. Once air is back, turn the press on and touch the yellow Shop Air Pressure icon, then put the platen back.

My Geo Knight DK20SP opens slower and slower.

The flow control valve under the front of the press is clogging, usually from wet or oily air. Geo Knight says to adjust or remove and clean it, and to drain your compressor daily.

Did this fix it?