Support
Machine type
Brand
Hotronix Auto Open Cap Press and 360 IQ Hat Press

Hotronix 360 IQ Hat Press setup: upper and lower heat, presets, pressure and hat loading tips

✓ Reviewed by Jason KimUpdated 3 min readFits: 360 IQ Hat Press (STXCP)
Short answer

Remove the packaging bolt, plug in and switch on. Set the top and bottom heater targets, time and pressure on the Home Screen or pick a preset. Lock a cap under the hold-down lever, pull the handle down and turn the pressure knob until the 0 to 9 readout matches your transfer. Turn on Target Temp so the press won't lock down before it is hot.

The 360 IQ Hat Press has an upper heater and a lower heater with a thermal pad, a cap hold-down lever, an electromagnet that holds the press closed, and a touchscreen. It shares its menus with the Hotronix IQ family, so presets, users and the IQ Portal work the same way as on a Fusion IQ.

First setup

  1. Remove the packaging bolt

    Take the packaging bolt out of the top of the press before you switch it on.

  2. Plug it in

    Push the power cord into the inlet on the side of the press and plug it into a grounded outlet. Hotronix lists a full 6 amp circuit at 120 V and 3 amp at 240 V, but says not to use any circuit under 10 amps, or one shared with another heat press or high-draw equipment. To unplug a locking cord, press the two red buttons while you pull the plug.

  3. Switch on

    Flip the power switch on. The Hotronix logo and software version show for a few seconds, then the Home Screen.

  4. Place it well

    Use a sturdy stand at least 36 in long, 24 in wide and 29 in high, and keep the area around the press clear.

Set temperature, time and pressure

The Home Screen shows the current top heater temperature, bottom heater temperature, pressure and time. Tap any of them to change the target, use the arrows for fine steps, then tap the check mark to accept or the X to cancel. Tap Off on a heater to turn it off.

To use a preset, touch the Columns icon and pick a material. Touch the Pencil icon to edit a preset or the Plus icon to create one; a new preset starts from the settings currently on the Home Screen. The circled numbers set extra steps for pretreatment or multi-step jobs. Managers have access to every setting; the default manager password is M.

Set the pressure

  1. Turn on Target Temp

    In Settings > System, turn on Target Temp. The electromagnet then won't lock the press down until it reaches temperature.

  2. Lock a cap in place

    Put a cap on the lower heater and lower the cap hold-down lever to lock it.

  3. Close and read

    Pull the lift handle down and read the pressure number on the Home Screen: 0 is none, 1 to 3 light, 4 to 7 medium, 8 to 9 heavy.

  4. Adjust

    Turn the pressure adjustment knob: clockwise adds pressure, counterclockwise reduces it. Check the reading again with the handle down.

  5. Fit the cap size

    For different cap sizes, loosen the knob on the lower heater and adjust its position.

Too much pressure can damage the press structurally, and Hotronix's limited warranty does not cover that damage.

Press a hat

When the press is at temperature, position the cap and design, lower the hold-down lever, and pull the lift handle down. The countdown starts on its own, and the heat platen lifts when the cycle ends.

Hotronix's loading tips

  • Hold the hat by the sides of the bill and slide it on from the side of the platen.
  • Line up the seam of the bill with the lip on the lower platen to reach the full print area.
  • Pull the sweatband out where you can, for a smoother press.
  • Cover the logo with the included pad that matches the thickness of your material.
  • Take the hat off the press before you peel the backing, so the adhesive can cool and set.
  • Leave emblems and patches alone for 24 hours.

Things to leave to us

The press comes calibrated from the factory, and Hotronix says calibration is only needed after a sensor or controller is replaced. Wrong calibration can ruin prints or damage the press, and that isn't covered by warranty. If you think the temperature or pressure is off, text us at (562) 609-4996 before you open the calibration menus.

Watch Hotronix's video: 360 IQ Hat Press, adjusting the pressure

More videos

Step by step heat printing with the 360 IQ Hat Press (earlier version)
Mastering the Hotronix 360 IQ: how to print hats

Embedded from the manufacturer's official channel.

Common questions

Why does the 360 IQ have a heated bottom platen?

Heat from below helps dimensional emblems, embroidered patches and leather patches bond reliably, because the hat is heated from both sides.

The press won't lock down. What's wrong?

If Target Temp is turned on, the electromagnet won't engage until the press reaches temperature. Wait for it to heat up.

The screen is orange. What does that mean?

The press is in Standby Mode and the platen is still above 100°F (38°C). The heater is off. Touch the Home icon to start heating again.

Can I turn one heater off?

Yes. On the Home Screen, tap the heater's target and choose Off.

How long before I can handle the patch?

Hotronix says not to pick at or pull an emblem or patch for 24 hours, so the adhesive can set fully.

Sources
Did this fix it?