Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Auto Open Cap Press setup: packaging bolt, temperature, two timers and pressure readout
Remove the packaging bolt on top, plug into a full 10 amp grounded circuit and switch on. Press Mode once to set temperature (176 to 430°F), a second time for Time #1, a third time for Time #2 and a fourth time to go back to print mode. Turn the knob clockwise for more pressure and read the 0 to 9 number on the display with the handle locked down.
The Auto Open Cap Press is a small clamshell press with a curved heat platen for hats. It runs from four controls on the LED panel: the display, a Mode Select button in the middle, and a decrease (-) and increase (+) button. This guide follows Hotronix's operator's manual from unboxing to your first cap.
Before you switch it on
-
Take out the packaging bolt
There is a shipping bolt (a thumb screw) on top of the press. Remove it before you turn the press on or try to close it.
-
Give it a sturdy stand
Hotronix calls for a stand at least 36 in long, 24 in wide and 29 in high, with a clean, clear work area around it.
-
Plug into the right outlet
A 120 V press needs a full 10 amp grounded circuit, and a 220 V press also needs a full 10 amp grounded circuit. Don't use a circuit that is smaller than that or already feeding another heat press or other high-draw equipment. If you need an extension cord, keep it short, heavy duty and no lighter than 12 gauge.
-
Switch on
The power switch is on the side of the press. Turn it on and let the press heat.
Hotronix warns that a weak or shared circuit causes erratic controls, wrong readings, slow heat-up and a tripped breaker on the press.
Set temperature and time
-
Temperature
Press Mode Select once. The SET and TEMP lights come on. Use + or - to set the temperature anywhere from 176°F (79°C) to 430°F (220°C). The display shows the change as you make it.
-
Time #1
Press Mode Select a second time. The SET and TIME lights come on. Set the first time with + or -.
-
Time #2
Press Mode Select a third time. All three red lights come on. Set the second time. For a single-hit job, make it the same as Time #1.
-
Back to print mode
Press Mode Select a fourth time. All lights go off and the press is ready to print.
Set and read the pressure
The pressure knob sits under the center of the heat platen, so pressure spreads from the middle out to the edges. Turn it clockwise to increase pressure and counterclockwise to decrease it. With the handle locked in the print position, a number from 0 to 9 shows at the lower right of the display.
| Readout | Pressure |
|---|---|
| 0 | No pressure |
| 1 to 3 | Light |
| 4 to 7 | Medium |
| 8 to 9 | Heavy |
Set the pressure with a cap on the platen, because the cap's thickness changes the reading.
Hotronix's limited warranty does not cover structural damage caused by too much pressure. Raise it a little at a time.
Press a cap
-
Wait for temperature
Let the press reach the temperature you set.
-
Load and lock the cap
Position the cap and the design, then lower the cap hold-down lever under the lower platen to lock the cap in place. It stops the hat shifting during the press.
-
Close the press
Pull the lift handle down. The timer starts on its own.
-
Let it open
When the time ends, the press releases and the gas shocks lift the heat platen. Keep your hands clear of the platen as it closes and opens.
Sleep mode
If the press sits unused for two hours, it drops into an energy saving sleep mode. Press any button on the panel to wake it, then wait for it to return to the set temperature before you press.
Optional cap platens fit low-profile, low-crown, full-crown and oversized hats. If the press still won't heat or won't hold down, see our cap press troubleshooting guide or text us a short video at (562) 609-4996.
Watch Hotronix's video: Cap Heat Press unboxing and set up
Embedded from the manufacturer's official channel.
Common questions
Which way do I turn the knob for more pressure?
Clockwise increases pressure and counterclockwise decreases it. Check the readout with the handle locked in the print position.
What pressure number should I use?
Hotronix groups the 0 to 9 readout as 1 to 3 light, 4 to 7 medium and 8 to 9 heavy. Follow your transfer's instructions and remember the cap itself adds thickness.
Why are there two timers?
Time #1 and Time #2 let you set different times for a two-hit application. For a single hit, Hotronix says to set both to the same time.
The display went dim and it isn't hot. Is it broken?
Probably not. After two hours without use the press goes into sleep mode. Press any button on the panel and let it come back up to temperature.
How does it open by itself?
An electromagnet holds the handle down while the timer counts. When the time is up, gas shocks lift the heat platen into the up position.
- Hotronix Auto Open Cap Press operator's manual
- Hotronix heat press FAQ
- AA support requests about Hotronix presses, 2024 to 2026











































































