Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Craft Press not heating, breaker tripping, settings won't change or residue on the platen
Most Craft Press problems are the circuit or the handle position. Hotronix wants a full 20 amp grounded circuit; a weak or shared one gives erratic controls, slow heat-up and a tripped breaker. Settings only change with the lift handle up, and the timer only starts when the press is locked down. Clean the cool platen with a dry cloth or abrasive-free mechanic's hand soap.
Use the table to find your symptom. Most fixes need nothing more than the right outlet or the handle in the right position.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| No display at all | Outlet, switch or press breaker | Power |
| Breaker trips | Circuit too small or shared | Power |
| Slow heat, jumpy display | Weak circuit or extension cord | Power |
| Buttons do nothing | Handle is down | Controls |
| Timer won't start | Press not locked down | Controls |
| Residue on the platen | Transfer stuck to the heater | Cleaning |
Switch off, unplug and let the press cool before you check or clean anything. Don't take the press apart. Hotronix says repairs should be done by a qualified service person.
Power
-
Check the circuit
At 120 V the Craft Press needs a full 20 amp grounded circuit. Hotronix says not to use a circuit under 15 amps or one already powering another heat press or high-demand equipment. An undersized circuit causes erratic controls, inaccurate displays, slow heat-up and a tripped breaker.
-
Lose the extension cord
Plug straight into the wall to test. If you must use a cord, keep it short, heavy duty and no lighter than 12 gauge.
-
Check the press breaker
The press has its own circuit breaker as well as the power switch. Reset it if it has tripped. If it trips again straight away, stop and contact us.
-
Check the cord
Never pull the cord to unplug; grasp the plug. If the cord is damaged, don't use the press.
Controls
- Buttons don't change anything: raise the lift handle. Temperature and time only change with the press on and the handle UP.
- Timer won't start: lower the heat platen and lock it fully into the press position. The timer starts on lock-down.
Cleaning
-
Cool and unplug
Let the heat platen cool completely and unplug the press.
-
Wipe it
Hotronix says transfer debris on its non-stick platens usually wipes off with a dry cloth.
-
For more
Use abrasive-free mechanic's hand soap on a cloth. Don't use scouring pads or anything that scratches the coating.
-
Prevent it
Check the transfer faces the garment and use a cover sheet over it.
Faint or patchy results
If the press heats but transfers come out faint in one area, check pressure before anything else. A slightly loose-feeling heat platen is normal, because Hotronix platens float to press evenly. To test, close the press on four slips of paper, one in each corner, and pull each one. If one slides out much more easily than the others, see our Craft Press pressure guide or send us a photo.
If the press is on a good circuit and still won't heat, or the display shows something odd, text us a short video at (562) 609-4996.
Common questions
My Craft Press heats very slowly. Why?
Usually the circuit. Hotronix says a circuit that is too small, or shared with other heat presses or high-demand equipment, causes slow heat-up and inaccurate displays.
The buttons don't do anything.
Raise the lift handle. Temperature and time are set with the press on and the handle in the UP position.
What should I clean the heat platen with?
Hotronix recommends a dry cloth for transfer debris, or abrasive-free mechanic's hand soap on a cloth. Let the press cool and unplug it first.
The cord is cracked. Can I keep using it?
No. Hotronix says not to operate a press with a damaged cord. The cord must be replaced by the manufacturer, its service agent or a similarly qualified person.











































































