Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Craft Press setup: power, stand, temperature, time and your first press
Place the press on a sturdy stand, plug it into a full 20 amp grounded circuit and switch it on. With the handle up, press Mode to step from the current temperature to the print temperature and the print time, using + and - to change each. Once it is hot, lay out the garment and transfer, lock the press down, and the timer starts on its own.
The Craft Press has a lift handle, a pressure knob on top, a control panel with a digital display, and a Mode, increase (+) and decrease (-) button. Its power switch and circuit breaker are on the press itself. Here is how Hotronix sets it up.
Set it up
-
Choose the spot
Put the press on a sturdy stand at least 36 in long, 24 in wide and 29 in high. Keep the work area clean and clear.
-
Plug it in
Use a properly grounded outlet. Hotronix calls for a full 20 amp circuit at 120 V. Don't use a circuit under 15 amps, or one shared with another heat press or other high-demand equipment.
-
Avoid long cords
If you need an extension cord, keep it as short as possible, heavy duty and no lighter than 12 gauge. Route it so it can't touch the hot platen or be tripped over.
-
Switch on
Turn on the power switch with the lift handle up, and let the press start heating.
Hotronix warns that an undersized or shared circuit causes erratic controls, inaccurate displays, slow heat-up and a tripped breaker.
Set temperature and time
With the press on and the lift handle in the UP position, press MODE to cycle through the setup screens.
| Screen | What it shows | How to change it |
|---|---|---|
| Ready | Current temperature (°F) | Nothing to set |
| Temp | Print temperature | + to raise, - to lower |
| Time | Print time in seconds | + to raise, - to lower |
Press MODE again to go back to the ready screen. Follow your transfer or vinyl maker's temperature and time.
Make your first press
-
Wait for temperature
Let the display reach the temperature you set.
-
Lay out the garment
Place the garment flat on the lower platen.
-
Place the transfer
Align the transfer on the garment. A cover sheet on top keeps adhesive off the heat platen.
-
Lock it down
Lower the heat platen and lock it into the press position. The timer starts on its own.
-
Open on the beep
The timer counts down and beeps when it is time to lift the heat platen. The time resets automatically for the next press.
Keep your hands clear of the upper platen as you lock it down, because the pressure can injure you. The heat platen is hot whenever the press is on.
If the transfer doesn't stick well, set the pressure next: see our Craft Press pressure guide. Still stuck? Text us at (562) 609-4996.
Common questions
Why won't the buttons change anything?
Temperature and time are set with the press on and the lift handle in the UP position. Open the press and try again.
Is the time in seconds?
Yes. The print time is shown and set in seconds.
Does the timer reset itself?
Yes. When the cycle ends and you lift the handle, the time resets for the next press.
Can I plug it into a power strip?
Hotronix calls for a full 20 amp grounded circuit at 120 V, and says not to share it with other heat presses or high-demand equipment. If you need an extension cord, keep it short, heavy duty and no lighter than 12 gauge.











































































