Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Mighty Mug settings: idle temperature, print temperature, print time and factory reset
With the handle open, press Mode once to set the idle temperature (205 to 300°F), twice for the print temperature (205 to 430°F), three times for the print time (1 to 999 seconds), and a fourth time to return to print mode. The press won't print while the SET light is on. Hold both outside buttons for about 5 seconds while idling to restore the factory defaults.
The Mighty Mug uses two temperatures. The idle temperature is where the heater waits between mugs. The print temperature is where it goes once you close the press around a mug. The print time counts down only after the print temperature is reached. All three are set from the Mode button in the center of the control panel.
Keep the handle in the open position when you switch the press on and whenever you change temperature, time or pressure.
Switch on
-
Plug in
Use a grounded outlet. A 120 V press needs at least a 4 amp circuit and a 240 V press at least 2 amp, but Hotronix says not to use a circuit under 15 amps or one shared with other high-demand equipment. Extension cords should be short and no lighter than 12 gauge.
-
Turn it on
Switch on at the power switch on the press, with the handle open.
Set the temperatures and time
-
Idle temperature
Press Mode once. The SET light comes on. Use the left (-) or right (+) button. The range is 205 to 300°F (95 to 149°C), default 205°F.
-
Print temperature
Press Mode again. The SET and TEMP lights come on. Set it the same way. The range is 205 to 430°F (95 to 221°C), default 390°F (199°C).
-
Print time
Press Mode a third time. The SET and TIME lights come on. Set 001 to 999 seconds.
-
Back to print mode
Press Mode a fourth time. All lights go off and the press is ready to print.
| Mode presses | Lights on | You are setting |
|---|---|---|
| 1 | SET | Idle temperature |
| 2 | SET and TEMP | Print temperature |
| 3 | SET and TIME | Print time |
| 4 | None | Back to print mode |
The press will not print while the SET light is on, because it is still in adjustment mode. If nothing happens when you close the handle, check the lights first.
Settings Hotronix starts you with
Out of the box the press is set to its lightest pressure, an idle temperature of 205°F (95°C), a print temperature of 390°F (199°C) and a print time of 2 seconds. Hotronix gives 390°F as the average print temperature for a mug, and says a full cycle takes about two minutes, because the heater has to climb from idle to print temperature before the timer runs. Always check your transfer paper and mug supplier's instructions too.
What the display shows
- The lowest temperature the display shows is 200°F (93°C). A cold press reads 200 until it is warmer than that.
- The lowest idle or print setting is 205°F. The highest idle is 300°F and the highest print temperature is 430°F.
Restore the factory defaults
-
Let it idle
The press must be idling in print mode with no lights on.
-
Hold both outside buttons
Press and hold the (-) and (+) buttons together for about 5 seconds, until all three lights begin to flash.
-
Check
The lights flash three times to confirm the factory defaults are back. Set your temperatures and time again.
If the settings won't change or the display behaves oddly, text us a short video at (562) 609-4996.
Common questions
What is the idle temperature for?
It is the temperature the heater waits at between mugs. When you close the press it heats up to the print temperature. Hotronix says a lower idle temperature helps extend heater life.
Why doesn't the timer start as soon as I close it?
The print time only starts once the heater reaches the print temperature. Hotronix notes a full cycle takes about two minutes.
Do my settings stay after I switch off?
Yes. The temperature and time you set become the new defaults until you change them.
What are the factory settings?
Idle 205°F (95°C), print 390°F (199°C), and a print time of 2 seconds, at the lightest pressure.
- Hotronix Mug Press operator's manual
- AA support requests about Hotronix presses, 2024 to 2026











































































