Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Mighty Mug not heating, timer not starting or breaker tripping
If the timer won't start, check that the SET light is off and that the press has reached its print temperature, because the time only counts down after that. A display stuck at 200 is normal on a cool press, since it doesn't show anything lower. A tripping breaker, slow heat or erratic display almost always means the circuit is too small or shared.
The Mighty Mug is simple, so most problems come down to a few things: the circuit, the mode the panel is in, and how the two temperatures work. Go through the table first.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Completely dead | Outlet, switch or press breaker | Power |
| Breaker trips or slow heat | Circuit too small or shared | Power |
| Display jumps around | Weak circuit | Power |
| Timer won't start | SET light on, or not at print temperature | Timer |
| Display reads 200 | Press is cooler than 200°F | Display |
| Settings keep resetting | Factory reset triggered | Display |
Unplug the press and let it cool before you check anything. If the cord is damaged, or the press has been dropped, stop using it. Hotronix says a damaged cord must be replaced by the manufacturer, its service agent or a similarly qualified person.
Power
-
Check the circuit
Hotronix says not to run the press on a circuit under 15 amps or one shared with other high-demand equipment, especially another heat press. An undersized circuit causes erratic controller behavior, inaccurate displays, slow heat-up and a tripped breaker.
-
Plug straight into the wall
Test without an extension cord. If you need one, it must be short, heavy duty and no lighter than 12 gauge.
-
Check the press breaker
The press has its own circuit breaker. If it has tripped, reset it once. If it trips again, stop and contact us.
-
Switch on with the handle open
Hotronix says the handle should be open when you turn the press on.
Timer
- SET light on: the press is in adjustment mode and won't print. Press Mode until all three lights are off.
- Not at print temperature yet: after you close the handle, the heater climbs from the idle temperature to the print temperature. The timer only counts down once it gets there, then beeps when the press should be opened.
- Handle not fully locked: close the handle all the way so it locks.
- Timer resets: opening the press resets the timer for the next mug. That is normal.
Display
- The display doesn't show temperatures below 200°F (93°C), so a press that is warming up reads 200 for a while.
- Your temperature and time settings are remembered when the press is off. If they jump back to 205°F idle, 390°F print and 2 seconds, someone has held the two outside buttons and restored the factory defaults.
When to contact us
If the press is on a good circuit, the SET light is off, and it still won't heat past 200 or won't count down, text us a short video of the display after you close a mug in it at (562) 609-4996. Don't open the control housing yourself.
Common questions
My display says 200 and won't go lower.
That is normal. The lowest temperature the Mighty Mug displays is 200°F (93°C).
I closed the press and nothing happens.
Check the panel. If the SET light is on, the press is still in adjustment mode and won't print. Press Mode until all lights are off.
It takes ages to finish a mug.
The timer only starts once the heater reaches the print temperature from idle. Hotronix says a full cycle takes about two minutes. A weak circuit makes heat-up slower.
My settings went back to the factory ones.
Holding the two outside buttons for about 5 seconds while idling restores the factory defaults. Set your temperatures and time again.
- Hotronix Mug Press operator's manual
- Hotronix heat press FAQ
- AA support requests about Hotronix presses, 2024 to 2026











































































