Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Lawson Silver-Jet daily cleaning and weekly maintenance: purging, tip soaking, Magic Clean and drawer slides
At the end of every day you spray, purge the Silver-Jet with distilled water until the lines run clear, take off the spray tip and soak it in distilled water or Magic Clean, brush it with a soft toothbrush, and wipe the inside of the unit with hot soapy water. Once a week (every few days in production), purge with Magic Clean, spray the drawer slides with silicone, and clean and oil the head rail.
Lawson puts it plainly: pretreat is glue suspended in saltwater. Whatever coats the shirt also coats the tip, spray head and pump, and if it dries there it clogs them. Skipping cleaning is the main cause of uneven spray patterns, and dried pretreat also corrodes the inside of the unit.
Never poke a needle or anything hard into the spray tip. It scores the metal opening and ruins the tip.
End of every production day
-
Purge with distilled water
Put the fluid hose in distilled water (hot is best) and cycle the unit until the lines are visibly clear of pretreat, usually 10 to 15 seconds. You can run it as if spraying a garment, or use the purge button with a container under the tip. Lawson says the importance of this step can't be overstated.
-
Soak the tip
Remove the quick exchange cap and soak just the spray tip in distilled water or Lawson Magic Clean until the next time you spray. Don't soak the rubber gasket that sits next to the tip inside the plastic nozzle.
-
Brush the tip
Clean the tip inside and out with a soft bristle toothbrush to remove salt deposits. If the opening is blocked, use the toothbrush and a can of compressed air.
-
Clean the inside
Wipe every inside surface with a sponge and very hot soapy water, then dry it. Left alone, the unit gets so caked and sticky that cleaning becomes a huge job.
Every week
-
Magic Clean purge
Put the fluid hose in Magic Clean and purge for 8 to 15 seconds. Production and multi-shift shops should do this every few days. Wear goggles and avoid eye contact. Then purge with distilled water to park the system.
-
Drawer slides
Spray the drawer slides with silicone spray or WD-40.
-
Head rail
Clean and lightly oil the head rail and the extrusion slide surface.
Spares to keep
| Part | Why |
|---|---|
| Spray tip | Keep at least one spare. How many you use depends on how often you spray, how well you purge and how well you maintain the unit. |
| Slip-on tube filter | Catches debris before it reaches the lines. Lawson suggests keeping four. |
| Spray valve | Cheap insurance for production shops |
| Fluid pump | For shops that can't afford downtime |
If the spray is already uneven after cleaning, see our uneven spray guide. For a valve or pump, text us at (562) 609-4996 with your Silver-Jet version.
Watch Lawson's video: Silver-Jet V2 features and care
Embedded from the manufacturer's official channel.
Common questions
Do I need to clean it if I only sprayed one shirt?
Yes. Lawson says the same cleaning applies whether you sprayed once or a hundred times.
Can I use tap water?
Only if you know it's clean and mineral free. Minerals leave deposits on the tip. Lawson recommends distilled water, ideally hot.
Can I clear a clogged tip with a pin?
No. A needle or any hard object will likely score the opening and ruin the tip. Use a soft toothbrush and compressed air.
Should I soak the rubber gasket with the tip?
No. Soak only the tip, not the rubber gasket inside the plastic nozzle.
What should I keep in stock?
At least one spare tip, about four slip-on tube filters, and if downtime would hurt you, a spare spray valve and fluid pump.











































































