Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Lawson Silver-Jet uneven spray pattern or patchy pretreat: causes and fixes
A partly clogged spray tip is the number one cause of uneven spray on the Silver-Jet. Clean the tip with Magic Clean and purge the whole system, and replace the tip if that doesn't fix it. Next check that enough pretreat is going down (slow the spray speed), that the drive wheel isn't slipping, that the pretreat hasn't settled or thickened, and that the post filter and pump aren't partly blocked.
A sprayer removes the two big causes of uneven hand spraying: overlap and changing speed. So when a Silver-Jet sprays unevenly, the cause is almost always in the fluid path, the amount, the travel speed or the pretreat itself.
Match your symptom
| What you see | Likely cause | Step |
|---|---|---|
| Streaks or a gap in the fan | Partly clogged tip | 1 |
| Thin, dry looking coat | Too little pretreat | 2 |
| Heavy and light bands | Drive wheel slipping | 3 |
| Sputtering or weak flow | Filter, pump or settled pretreat | 4 and 5 |
Step by step
-
Clean or replace the tip
This is the number one cause. Tips clog when you don't purge right after spraying, don't purge for at least 10 seconds, skip the weekly Magic Clean purge, or work in a hot shop. Remove the tip, soak it in Magic Clean and brush it with a soft toothbrush, then purge the whole system with Magic Clean followed by distilled water. If the pattern is still uneven, fit a new tip. Never use a needle on the opening.
-
Put down more pretreat
Decrease the spray speed so more lands on the garment. Different garment brands and types need different speeds, which you'll learn with experience. For hard garments some printers speed up and spray twice. A tip that passes less fluid (WENA or OENA) also changes the amount.
-
Check the travel
The spray head must move at a steady speed. On the Silver-Jet that depends on the drive wheel pressure being set correctly; if the wheel slips, the coat bands. Lawson shows the adjustment in a video. Text us and we'll walk you through it.
-
Check the pretreat
Some pretreats separate so the binder, salt and water are no longer even, or get too thick. Mix or replace it. For polyester pretreat, use Lawson's polyester tip (WENF).
-
Filter, pump and head position
Lawson's troubleshooting chart also lists replacing the post filter, a partly clogged spray pump, and centering the spray head. Replace the slip-on post filter first; it's cheap. Pump replacement and head centering we'll talk you through.
Keep it from coming back
- Purge for at least 10 seconds with distilled water right after you finish spraying, every day you use the sprayer.
- Run Magic Clean through it at least weekly, or every few days if you run shifts.
- Soak and brush the tip at the end of the day and keep a spare tip in the drawer.
- Keep the pretreat mixed, and keep the room from getting hot.
Send a photo of a sprayed shirt on a dark surface and your speed setting to (562) 609-4996 and we'll help narrow it down.
Watch Lawson's Silver-Jet overview
Embedded from the manufacturer's official channel.
Common questions
How long should I purge after spraying?
At least 10 seconds, right after you finish, and with Magic Clean at least once a week.
Does heat matter?
Yes. Lawson lists hot shop conditions as a cause of clogs, because you're spraying a glue.
I'm spraying polyester. Do I need a different tip?
Lawson makes a polyester tip (WENF) for polyester pretreats.
Should I roll or brush the pretreat after spraying?
Lawson says some printers roll or brush left to right to even it out, but calls it a controversial technique. Try it and judge the print.
How do I adjust the drive wheel?
Lawson covers drive wheel pressure in a video on its customer page. Text us and we'll walk you through it.











































































