Support
Machine type
Brand
Epson SureColor F2100

How much DTG pretreat to use, and which pretreat for cotton, blends and polyester

✓ Reviewed by Jason KimUpdated 2 min readFits: Mister-T2 · Viper XPT-1000 · Viper MAXX · FIREBIRD pretreats
Short answer

Measure pretreat in grams on the shirt, not by the number on your sprayer. Weigh a rolled-up shirt before and after spraying, then compare the grams to the pretreat maker's chart for that garment. As a starting point, Ecofreen suggests about 10 to 20 grams on light cotton and 20 to 35 grams on dark cotton, and FIREBIRD's FBX-VIVID chart recommends about 14 to 35 grams per 14 x 17 inch area. Then fine-tune with a step test and a wash test.

Step 1: Measure what actually lands on the shirt

The number on your sprayer isn't grams. Ecofreen says the Mister-T2 display is only a guide, Viper's laydown charts are approximate, and every spray tip puts down more as it wears. Weigh it. This is Viper's method:

  1. Tare a rolled-up shirt

    Use a scale that reads to 0.1 gram. Roll the shirt up, set it on the scale and zero it.

  2. Spray, re-roll and weigh

    Pretreat the shirt, roll it back up and weigh it. The reading is the grams of pretreat on the shirt.

  3. Work out grams per square inch

    Measure the sprayed area and multiply width by height. Divide the grams by the square inches. For example, 19.3 grams over 15 x 16 inches (240 square inches) is about 0.08 grams per square inch.

  4. Compare and record

    Multiply that figure by the area your pretreat maker quotes (for example 14 x 17 inches) and compare with their chart. Write down the sprayer setting and the grams for every shirt style you run.

Step 2: Start from the maker's numbers

Source Garment Starting amount
Ecofreen (Mister-T2 chart) Light cotton 10 to 20 g, one-direction spray
Ecofreen (Mister-T2 chart) Dark cotton 20 to 35 g, two-direction spray
Ecofreen (Mister-T2 chart) Polyester About 30 g
Ecofreen (Mister-T2 chart) Blended hoodie About 50 g
FIREBIRD FBX-VIVID Light garments, CMYK printing About 14 to 35 g per 14 x 17 inch area (0.06 to 0.15 g per square inch)
FIREBIRD FBX Ghost White, light and medium colors 15 to 40 g per 14 x 16 inch area
FIREBIRD FBX-NOVA White-ink printing Use FIREBIRD's FBX-NOVA T-shirt matrix

Ecofreen's chart was written for its own pretreat. Use it as a sprayer starting point and let your pretreat maker's numbers win when they differ.

Step 3: Dial it in with a step test

Viper's step test sprays one shirt in six columns, each a bit heavier than the last (the MAXX default runs from about 11 to 35 grams in roughly 5 gram steps). Dry it, print a solid white box across all six, and look for the column where the white stops getting more opaque. That column, or a setting between it and the next, is the right amount for that shirt. On the MAXX this is under Utilities > Spray Test on firmware HMI5001 PLC3020 or newer. On other machines, spray strips at different settings by hand.

Cotton, blends and polyester

  • Heavier and darker garments take more. Viper notes the right amount depends on the pretreat's dilution, the shirt's weight and its color.
  • Polyester: use a pretreat that its maker says works on polyester. FIREBIRD lists FBX-VIVID (cotton, blends and polyester, CMYK on light garments) and FBX Ghost (CMYK-only on white cotton and 100% polyester). Dry it with that pretreat's own settings.
  • Hoodies, tri-blends, CVC: FIREBIRD positions FBX-NOVA for these with white ink.

Every maker says the same thing: run a test print and a wash test on each new garment style before you sell it. Keep a log of grams, sprayer setting and press settings per style.

Seeing stains, a halo or a yellow box after pressing? Text us a photo of the front and inside of the shirt at (562) 609-4996, along with your pretreat, grams and press settings.

Watch Viper's video: changing the amount of pretreatment on the MAXX

Embedded from the manufacturer's official channel.

Common questions

My sprayer's display says 30. How many grams is that?

You can't tell without weighing. Ecofreen states that the volume shown on the Mister-T2 display is for general information only and isn't an accurate measure, and tip wear changes the amount over time. Weigh test shirts.

Which FIREBIRD pretreat should I use on polyester?

FIREBIRD says FBX-VIVID works on cotton, blends and polyester for CMYK printing on light garments, and that FBX Ghost enables CMYK-only printing on white cotton and 100% polyester and suits light and medium colors. FBX-NOVA is for white-ink printing, including hoodies, tri-blends and CVCs. Always run a test print and wash test.

How do I dry the pretreat?

Follow your pretreat maker. FIREBIRD lists 330°F for 20 to 40 seconds at medium pressure for FBX-NOVA, until the steam stops, and 320 to 340°F for 20 to 30 seconds at light to medium pressure for FBX-VIVID. Ecofreen's chart for its own pretreat uses 320 to 338°F for 60 to 70 seconds on dark cotton and 320°F for 90 seconds on polyester. If the shirt isn't dry, press it again.

Does it matter if I mix two pretreats in the sprayer?

Yes. Ecofreen warns that different pretreats can react in the lines and clog the nozzles. Flush with water between them.

Is more pretreat always brighter?

No. Viper's step test looks for the point where adding more stops making the white more opaque. That's your amount for that shirt. Going past it just wastes pretreat.

Did this fix it?