Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Mimaki TxF330-800 error messages and nozzle clogging: what the display means and what to do
Most TxF330-800 messages ask for something simple: close a cover, lower the clamp lever, reload the film straight, swap ink, or clean the wiper or NCU. Clogging that head cleaning won't clear gets Mimaki's Nozzle Wash, first with a 1 minute soak and then 10 minutes. Board, head, motor and PCB errors call for a restart. If one comes back, note the number and contact us.
When something goes wrong, the TxF330-800 beeps and shows a message. The status lamp flashes or stays red on an error. These are the messages Mimaki's manual lists, grouped by what you do about them.
Messages you can clear yourself
| Message | What it means | What to do |
|---|---|---|
| COVER OPEN | A cover is open | Close it |
| Lower the clamp lever, 504 CLAMP UP | Clamp lever is up | Lower it |
| MOTOR POWER OFF | Motors stopped after a cover opened | Wait for initialization to finish |
| Data Remain, 902 | A job arrived in LOCAL mode | Switch to REMOTE, or DATA CLEAR |
| No Media, Media Undetected | No film, or width not read | Load the film and detect the width. Clean the media sensors. |
| 505 Media Jam | Jam sensor tripped | Remove the film touching the carriage, check nothing blocks it, reload fresh film |
| 516 Media Set Position R, 50c | Film loaded too far right, or width not read | Reload in the marked position. Clean the media width sensor. |
| Feeding Wrong | Film skewed or lifting, or torque limiter too high | Reload straight, lower the torque limiter, detect the width again |
| 90f Print Area Short | Film too small for the job | Use wider or longer film, or move the origin |
| Check Waste Ink tank (80%), Replace Wasteinktank (90%) | Waste count is high | Check the tank, replace it, reset the waste level |
| WashLiquidCart.None, Washing liquid end | Maintenance liquid missing or empty | Load a new maintenance liquid cartridge |
| Replace Wiper | Wiper count reached | Replace the wiper and reset the count |
| Wiper Move Failure, 406, SYSTEM HALT 406 WIPER ORG | Wiper not moving correctly | Clean the wiper and around it, then restart |
| High or Low ambient temp | Room outside the range | Bring the room back to 20 to 30°C |
| Auto-correction failed | Film not white or clean, lifting, or DAS sensor dirty | Load clean white film flat, clean the DAS sensor, or correct manually |
| NCU Sensor Lv Low, Nozzle check failed | Dirty nozzle check unit | Clean the NCU |
| No maintenance for ** days | Maintenance overdue | Do the maintenance using Carriage Out |
Ink messages
- Ink cartridge check (under 100 ml) and Ink Level Low (under 60 ml): take the cartridge out, weigh it and enter the weight. After Ink cartridge check, open the lid and fold the ink pack over, with the connector firmly in its slot.
- Ink Lvl End (under 30 ml), Replace Ink Pack, 602 Ink End, Remaining ink 0: replace the ink pack.
- No Cartridge, 608 Wrong Ink IC, 627 Re-insert Cartridge: reseat the cartridge and restart. Replace it if the error stays.
- Ink Color, Ink Type: the wrong cartridge is in that slot. Put in the right one.
- Can't Print/Cartridge, 628 Wrong Cartridge: replace with a new cartridge, and check for clogged nozzles.
Head cleaning won't run while Ink Level Low, Ink Near End or Ink End is showing. Correct the cartridge weight first, or replace the pack.
When nozzles stay clogged
-
Do the routine cleaning
Wiper, cap rubber and carriage underside. Our maintenance guide covers them.
-
Head cleaning, Normal then Hard
TEST PRINT/CLEANING > Cleaning, then test print. For white, follow with White Recovery Normal, then White Recovery Hard.
-
Nozzle Wash, 1 minute
MENU > Maintenance > Station Maint. > Nozzle Wash. Clean the wiper and bracket, press ENTER, clean the cap rubber, close the cover and press ENTER. Check the cap filled with maintenance liquid (top up by syringe if not), close the cover, set the soak time to 1 minute and press ENTER. Test print.
-
Nozzle Wash again, 10 minutes
Repeat with a 10 minute soak and test print. If it still isn't clear, contact us.
If ink drips from the nozzle surface onto the film, Mimaki's fix is wiper, cap and carriage underside cleaning, a head cleaning, and setting up auto maintenance. For dripping white, it lists White Maintenance > Hard.
Errors that need a restart or service
For main PCB, head connection or temperature, SDRAM, linear scale, pump motor, motor overload (401 to 404), NCU connection and heater temperature (710) errors, Mimaki's fix is to turn the power off, wait a while and turn it on again. For a motor error, first check the film is loaded correctly and nothing blocks the carriage. If the same number comes back, or you see Replace NCU, Replace NCU Ink Pad, D-Pump Replacement, Wh Damper Replacement, Battery Exchange or an ink leak, write down the message and contact us. For an ink leak, turn off the main power and unplug the printer first.
Common questions
What does Data Remain mean?
The printer received a job while in LOCAL mode. Switch to REMOTE to print it, or use DATA CLEAR to drop it.
Why does Ink cartridge check appear when there is still ink?
The printer estimates ink use. Under 100 ml it asks you to weigh the cartridge and enter the weight, then fold over the ink pack. Without the fold, ink can stop feeding.
The ink says Expiration. Can I keep printing?
Yes, up to one month past the date, but use it up fast. Two months past, the printer won't print with it.
What is Error 201 Command Error?
The print data was bad, or a USB flash drive was pulled from the RIP computer without Safely Remove Hardware. Clear the data and resend, check the USB cable, then restart the printer.
The display says Replace NCU or Replace NCU Ink Pad. Can I do that?
No. Those are service jobs. Contact us.











































































