Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Mimaki TxF330-800 setup: connecting the PC, RasterLink, loading film and your first test print
Turn the printer on with the END/POWER key, connect the RIP computer by gigabit Ethernet (Mimaki's recommendation), install the Mimaki driver and RasterLink, then register the TxF330-800 in RasterLink and download its color profile. Load the film, let the heaters reach temperature, print a test pattern, clean only if the pattern shows faults, run feed and drop position correction, and send the job from RasterLink.
This follows the print workflow in Mimaki's TxF330-800 Operation Manual. If your printer was installed by a technician, the first steps are already done, and you can start at step 6.
-
Power on the right way
Make sure the main power switch is on, then press END/POWER. The firmware version shows and the printer settles into LOCAL mode. Close the front and maintenance covers: with a cover open the automatic anti-clog maintenance can't run. From now on, turn the printer off only with END/POWER and leave the main switch on.
-
Connect the RIP computer
Use a Category 6 or 6A LAN cable to a gigabit (1000BASE-T) computer or switch on the same network. The printer can't be reached through a router. Check the display: if it shows 100Mbps, 10Mbps or No Connect, it won't print. USB 2.0 also works, but data can arrive too slowly and the carriage may pause at the ends.
-
Install the Mimaki driver and RasterLink
Download the driver from Mimaki's inkjet download page under TxF330-800 > Driver/Utility and install it. Install RasterLink and activate its license. Mimaki warns that Profile Update won't start until the license is activated.
-
Register the printer and get its profile
Open RasterLink. In Printer Management click Add, pick the model, the ink set you have loaded, the output port and the TxF330-800 it finds, then click OK and Yes. Download the color profile for your film and ink set, either through RasterLink's profile download or from Mimaki's site under TxF330-800 > Profile.
-
Leave the head height alone unless you change film
The head gap ships at Low (1.6 mm). Middle and High exist for thicker media. If you ever change it, Mimaki requires a drop position correction afterward. Text us before changing it.
-
Do the before-work cleaning
Clean the wiper and bracket, the cap rubber and the underside of the carriage. Our TxF330-800 maintenance guide walks through each one.
-
Load the roll
Let new film sit in the print room for at least 30 minutes first, and don't use curled film. With two people, raise the clamp lever, set the rear roll holders to half the film width on the scale (for 600 mm film, both edges on 30), feed the film between the pinch and grit rollers, then pull it out 10 to 20 cm past the platen with even tension on both sides and lower the clamp lever. Fit the media holder, press the roll key and choose Roll to detect the width.
-
Set the heaters
Select HEATER on the LOCAL screen and enter the pre, print and post temperatures. Printing can start once each is within 3°C of its setting. If you print from RasterLink, the profile's temperatures take priority.
-
Print a test pattern
Select TEST PRINT/CLEANING > Test Print, choose Scan Dir. or Feed Dir., and press ENTER. Film for the test must be at least 500 mm wide. Look for bent lines (deflection) and missing lines (clogging).
-
Clean only what the pattern shows
Go to TEST PRINT/CLEANING > Cleaning, pick the type, tick the heads to clean and press ENTER. Use Soft for bent lines, Normal for missing lines, Hard if those fail, then White Recovery Normal and White Recovery Hard if white still won't come back. Test print again after each round.
-
Run the corrections
Select ADJUST > Auto-correction and run Feed Comp. and Drop.PosCorrect. The printer prints, reads and sets the values itself. It needs clean white media at least 250 mm wide that lies flat. If auto-correction fails on your film, use the manual Feed Comp. and Drop.PosCorrect under ADJUST instead: print the pattern, enter the value where the bands blend evenly or the lines meet, and press ENTER. Redo feed correction whenever you change film or feeding unit settings.
-
Send the job
In RasterLink open the file, select the TxF330-800 tab, choose the profile under Quality, then Execute with RIP and Print. After changing the roll, click Update the printer status so RasterLink knows the new width. To stop a job, press LOCAL to pause, or use DATA CLEAR to clear it.
Don't move the carriage by hand. Use the carriage out options in the Maintenance menu whenever you need it over the platen.
Common questions
Ethernet or USB?
Mimaki recommends Ethernet. It needs a Category 6 or 6A cable and gigabit (1000BASE-T) hardware on the same network, not through a router. Over USB the carriage can pause at the ends while it waits for data.
The display shows 100Mbps or No Connect. Can I print?
No. Printing needs a 1000 Mbps link. Check the cable category, the switch and the computer's network port.
My computer has Wi-Fi on and keeps losing the printer. Why?
Mimaki notes this can happen when the PC is on Wi-Fi and the printer is on Ethernet, especially if the IP address starts with 169.254. Turn off Wi-Fi on the PC, or set fixed IP addresses on both.
What heater temperature should I use?
The color profile in RasterLink carries Mimaki's recommended values and overrides the panel setting. Use the profile for your film and ink set.
Which head cleaning should I run first?
Soft for bent lines, Normal for missing lines, and Hard only if those fail. Repeat test print and cleaning until the pattern is clean.











































































