Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro 36 Pro end-of-day maintenance: cooldown, filter rotation, oil drain, sponge and powder station
Set all four heating zones to 0 and let the fume extractor run with the covers open for 10 to 20 minutes before powering off. Wipe the oven (never the heating lamps), swap the cold catalyst and carbon filters for a dry spare set every day or 100 m, open the oil drain valve overnight and clean the drip tray, and wipe or replace the sponge. Never wash the filters or the sponge.
The Miro 36 Pro collects the oil from curing ink in a drain system and a sponge, and filters its fumes through a cold catalyst filter and an activated carbon filter. Look after those three things daily and it stays clean and smoke-free. You need gloves, a clean cloth, cleaning solution, isopropyl alcohol and a brush.
| When | What to do |
|---|---|
| End of every day | Cool down with the fume extractor, wipe the oven, swap in the dry spare filter set, open the oil drain, check the sponge, clean the powder station |
| Every 100 m of printing, or daily | Rotate the filters |
| When filters blacken | Replace the filter set, also if smoke appears soon after fitting a filter |
| Before the next session | Close the drain valve and make sure the collection box is clean |
Shut down and cool
-
Turn the heat off
Tap each of the four heating zones, enter 0 and tap Confirm.
-
Let it clear
Leave the fume extractor on. Open the powder station cover and the oven cover and let the machine cool for 10 to 20 minutes, with the extractor running at least 10 minutes to clear the smoke. Then tap Fume Extractor to turn it off.
-
Power off
Press the upper power switch, then the lower one, and unplug both cords at the back.
Clean the oven
Wipe the inside of the oven cover around the heating lamps, and spray cleaning solution onto the cloth (not the plate) to wipe the whole main heating plate edge to edge. Brush powder out of the back corners and along the back edge. Close the cover and latch it.
Don't wipe or touch the heating lamps themselves. A broken lamp has sharp edges. A spare lamp ships with the machine; contact us before fitting it.
Filters
-
Take them out
Open the cabinet door and pull out the top filter by its strap, then the one below it. Wipe out the filter compartment.
-
Dry, don't wash
Never wash the cold catalyst filter or the activated carbon filter. Let them air-dry in a cool, dry, shaded spot and put them back only when completely dry. Keep a second set so you can fit it while the first one dries.
-
Refit in order
Slide the activated carbon filter into the bottom slot and the cold catalyst filter into the top slot, with the THIS SIDE UP label facing up. Raise the seal to make room as you slide them in.
Oil drain and sponge
-
Open the drain
After the day's printing, open the drain valve and leave it open overnight so the oil runs into the collection box.
-
Clean the drip tray
Pull out the drip tray below the valve, clean it with a cloth dampened with isopropyl alcohol and slide it back. Close the cabinet door. Close the valve before the next print session.
-
Check the sponge
If it's only slightly oily, wipe it with a dry cloth and let it air-dry in a ventilated, shaded spot. If it has been heavily saturated for a long time, or has turned brittle, don't wash it: replace it with a new sponge.
Powder station
-
Wheels and sensor
Open the powder station cover, lift out the media wheel rod and brush the wheels. Brush out the station and wipe the media sensor gently with the cloth.
-
Trays
Pull out the powder tray, then the second tray. Brush the station floor again and sweep the ledge into a tray held underneath. Dispose of the waste powder and slide both trays back.
-
Finish up
Refit the media wheel rod with the two wheels at one end next to the sensor, then set the wheel at the other end. Close the cover, wipe and fold down the front heating plate, wipe the top of the machine and put the dust cover on.
Smoke appearing quickly after a fresh filter, or oil dripping where it shouldn't? Text us a photo or short video at (562) 609-4996.
Watch DTF Station operate and maintain the Miro 36 Pro
Embedded from the manufacturer's official channel.
Common questions
Can I wash the Miro 36 Pro filters?
No. Let them air-dry in a cool, shaded place and refit them only when completely dry. Replace them when they turn black and saturated, or if smoke appears soon after fitting one.
How often do I rotate the filters?
Every 100 meters of printing or at the end of each day, whichever comes first. Keep a spare set so one can dry while the other works.
Which filter goes on top?
The cold catalyst filter goes in the top slot and the activated carbon filter in the bottom slot, label up.
When do I open the oil drain valve?
After the day's printing. Leave it open overnight, then close it before you print again.
The sponge is soaked. Can I rinse it?
No. A lightly oily sponge can be wiped dry and aired out. A heavily saturated or brittle one should be replaced.
- DTF Station: Miro 36 Pro quick start guide
- DTF Station: Miro 36 Pro user manual
- DTF Station technical documentation
- AA support requests about the Miro 36, 2024 to 2026











































































