Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro 13 and 13 Max take-up reel or shaking paddle not working
A take-up reel that stops, starts on its own or never turns is usually the film sensor (often just powder on it), then the relay, then the motor. Clean the sensor first, then read its lights: green means it has power, orange means it sees the film. If the shaking paddle stops, check that the paddle rod is locked to the motor before suspecting the motor itself.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Take-up stops and starts, or stops after a while | Powder on the film sensor, or a failing relay | Steps 1 to 5 |
| Take-up won't stop turning | Sensor stuck on (powder on its face) | Step 4 |
| Take-up never turns at all | Power supply, relay or take-up motor | Steps 2, 5 and 6 |
| Shaking paddle doesn't move | Loose paddle lock, unplugged wire, or motor | Steps 7 to 9 |
Turn the shaker off and let it cool before you remove any panel. A few checks below need the power back on so you can read indicator lights: look, but keep hands and tools away from the wiring while it's live.
Take-up reel
-
Open the side panel
With the power off, take out the powder tray and remove the seven Phillips screws holding the side panel. Lift the panel away.
-
Check the power supply light
Turn the power on and find the main power supply. A blue light means it's working. If the blue light is off, the power supply may have failed, and the relay and sensor won't show any lights either.
-
Read the film sensor lights
The sensor sits in an opening on the side of the cabinet. Look at it from the opposite side. Green means it has power. Cover it with the media rod: the orange light should come on. No lights at all points to a faulty sensor.
-
Clean the sensor
If the orange light stays on with nothing in front of it, powder has built up on the sensor. Turn the power off and wipe its face gently with a soft dry cloth, then test again. Wiping around the sensor as part of your daily cleaning keeps it from coming back.
-
Test the relay
The relay is a small clear cube. Trigger the sensor and listen for a click, and look for its green light. If the sensor turns orange but the relay neither clicks nor lights, the relay is the likely fault.
-
Test the take-up motor
Make sure the motor's power plug is pushed fully in. The black toggle switch on the motor runs it in either direction. If it won't run from its own switch, the motor is the likely fault. If the reel turns backwards and lets the film go slack, check that switch's position.
Shaking paddle
-
Check the paddle lock
Wiggle the paddle rod side to side. If it moves freely or slides out easily, the bearing lock has worked loose. Tighten the lock screws as firmly as you can, turn the power on and watch that the lock and rod now turn together.
-
Check the motor wire
Power off, remove the powder tray, loosen the side screws and open the side panel. Find the paddle motor's wire and make sure its plug is fully seated. Close up and test.
-
Test the motor on its own
Power off. Use a 2 mm hex driver to release the paddle from the motor shaft and set it aside, then turn the power on. If the motor makes no sound and doesn't turn, it needs replacing. Contact us and we'll confirm the part.
Still stuck? Record a short video showing the lights and the reel or paddle, and text it to (562) 609-4996.
Watch DTF Station's video: troubleshooting the Miro 13 Max take-up reel
Embedded from the manufacturer's official channel.
Common questions
The take-up reel won't stop turning. What does that mean?
The sensor thinks film is always there. If its orange light stays on with no film in front of it, wipe the sensor face with a soft dry cloth and test again. Powder on the sensor is the usual cause.
I already replaced the relay and the reel still acts up. What next?
Check the sensor lights and the power supply light before buying more parts. If the sensor shows orange when triggered and the relay clicks, test the motor with its own switch. Send us a video and we'll tell you which part it is.
Is this the same on the Miro 24?
The Miro 24 uses a similar film sensor, relay and take-up motor, but DTF Station's step-by-step video covers the Miro 13 Max. Text us before opening a Miro 24.
Will opening the side panel void my warranty?
Talk to us before you replace any part. We'll confirm the fault and the correct part first.
- DTF Station: How to troubleshoot an unresponsive take-up reel on Miro 13 Max
- DTF Station: Miro 13 and 13 Max powder shaking paddle and motor
- DTF Station: Miro 13 Max user manual (PDF)
- DTF Station: Miro 13 Max operation guide
- DTF Station technical documentation
- AA and DTF Station support requests about Miro take-up reels and shaking paddles, 2024 to 2026











































































