Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro shaker temperature wrong or not heating: default settings and calibration
DTF Station ships the Miro 13 Max and Miro 24 set to 130°C on the main plate and 80°C on the preheating plate, and its operation guides suggest starting the preheat lower, around 50°C. If prints cure poorly, measure the plates with an infrared thermometer before changing settings. If the display is off from the real temperature, enter the difference as an offset (PB1 for the main plate, PB2 for the preheat plate on the 13 Max and 24).
Default temperatures
| Model | Preheating plate | Main heating |
|---|---|---|
| Miro 13 Max | 80°C factory default; operation guide starts at 50°C | 130°C |
| Miro 24 | 80°C factory default; operation guide starts at 50°C, up to 80°C | 130°C factory default; operation guide uses 135°C |
| Miro 36 | 60°C | 130°C |
| Miro 36 Pro | 80°C front heating | 130°C main, plus 75°C on the front and rear heating bulbs |
These are starting points. A cold room or high altitude can call for more heat. Judge by the print: a cured transfer has a glossy orange-peel texture, and a grainy one needs more main heat.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Display and thermometer disagree | Temperature offset | Steps 1 and 2 |
| Miro 13 or 13 Max plate not heating, or display blank | Loose wire, then heating plate or display | Step 3 |
| Miro 36 shows an impossibly high temperature | Cable between the two units not seated | Step 4 |
| Miro 24 clicks repeatedly with a blinking LED | Power supply resetting because a part is overloading it | Step 5 |
Step by step
-
Measure the real temperature
Let the shaker heat and settle. Unlock both side buckles, open the main heating lid and read the plate with an infrared thermometer. Read the preheating plate the same way. Note the difference from the display for each.
-
Enter an offset (Miro 13, 13 Max and 24)
Long-press the ISIT button until the display shows the C section. PB1 is the main plate offset and PB2 is the preheating plate; both default to 0. Enter the real temperature minus the displayed one. For example, if the display says 130°C and the thermometer reads 120°C, set PB1 to -10. Long-press ISIT to save, close the lid and lock the buckles, then confirm the two readings now match. On the Miro 36, use Advanced Settings > Temperature Calibration. On the Miro 36 Pro, DTF Station asks that calibration be done with a technician, so contact us first.
-
Miro 13 or 13 Max plate not heating
Turn it off, unplug it and let it cool fully. Open the top heating chamber and lift the heating plate gently toward the back, without pulling it far enough to strain the wires, and mind the sharp edges. Gently tug the heating plate and display wires and tighten any loose screws. Power up and test. If it still won't heat, the plate's sensor or the temperature display may have failed. Contact us and we'll help you test it and confirm the part.
-
Miro 36 reads impossibly high
Turn it off. Turn the locking knobs counterclockwise and pull the powdering unit away from the oven. Check that all three cables between the units are pushed fully in, and turn each locking ring clockwise. Power up and recheck. If it reads normally, tidy the cables, make sure the oven's feet are on the floor, push the units back together and lock the knobs clockwise. If it's still wrong, contact us.
-
Miro 24 clicking and blinking
Repeated clicking with the side LED blinking in time means the power supply keeps resetting. Finding the cause means disconnecting internal parts one at a time, so stop using it and contact us. We'll walk you through it.
Only lift heating plates when the machine is unplugged and cool. Replace heating elements only after a technician has confirmed the fault.
Text a photo of the display next to your thermometer reading to (562) 609-4996.
Watch DTF Station's video: calibrating Miro 13 and Miro 24 heating plates
Embedded from the manufacturer's official channel.
Common questions
What temperatures should I use on my Miro?
Start with the defaults in the table on this page, then adjust for your film and room. Color Prime powder and Glide Pro film list a 125°C (257°F) cure in a shaker. Raise the main plate if prints come out grainy.
Why is the preheating plate there at all?
It removes moisture and static from the film before powdering and helps stop excess ink spreading. Start around 50°C and raise it toward 80°C only if powder sticks to bare film.
I'm using Flex powder on a Miro 36. Anything different?
Yes. Color Prime says to run the main heating above 300°F (149°C) for Flex powder on the Miro 36 with an Epson G6070, and to press with a cold peel.
Should I change Celsius to Fahrenheit?
On the Miro 36 and 36 Pro you can switch units in the advanced settings. Just be sure which unit you're reading before you change a number.
- DTF Station: Miro 13 (Max) and Miro 24 temperature calibration
- DTF Station: Miro 13 and 13 Max main heating plate and temperature display
- DTF Station: Miro 36 main and preheating elements
- DTF Station: Miro 24 power supply clicking noise
- DTF Station: Miro 13 Max user manual (PDF)
- DTF Station: Miro 24 user manual (PDF)
- DTF Station: Miro 36 Pro user manual (PDF)
- DTF Station: Miro 24 operation guide
- DTF Station: Miro 36 operation guide
- Color Prime Flex Hot Melt Powder, product page
- DTF Station technical documentation
- AA and DTF Station support requests about Miro temperature settings and heating, 2024 to 2026











































































