Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Phoenix Air 16x20 oven not heating, curing unevenly, or smoking
Most Phoenix Air curing complaints come from a short preheat, the purifier running while the oven heats, or film placed off the center of the heater. Preheat about 10 minutes with the purifier off, center the sheet, start at the manual's 140°C (284°F) for 60 seconds, and check the plate with an infrared thermometer at the center and corners. If one area reads far off, or the oven keeps heating past its set point, stop and contact us.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Whole sheet grainy or sandy after curing | Too little heat or time, or a short preheat | Steps 1 to 3 |
| Some areas glossy, others grainy | Sheet off center, or one area of the plate running cool | Steps 3 and 4 |
| Sheet scorched, film hard to peel later | Too hot or too long | Steps 1 and 4 |
| Smoke from the purifier | Saturated filter | Step 5 |
| Won't reach temperature, keeps climbing past it, or won't power on | Heater, controller or power fault | Step 6 |
Step by step
-
Set temperature and time
Press the set button for temperature, use the up and down buttons, and press set again to exit. Do the same for time. The manual's suggested starting point is 140°C (284°F) and 60 seconds. Check your film's own instructions too.
-
Preheat properly
Turn the oven on about 10 minutes before your first cure, with the purifier switched off. Turn the purifier on only while the cure timer is running.
-
Center the sheet
Place the powdered film in the tray centered over the heater. The oven takes sheets up to 16 x 20 inches (40 x 50 cm). Press start; it beeps when the time is up. Take the film out, then press start again to stop the alarm.
-
Measure the plate
After preheating, read the plate with an infrared thermometer at the center and all four corners. If one zone is well below the rest, or the center reads very different from the display, take a photo of the display and write down your readings, then contact us. Don't try to fix uneven heat by turning the temperature way up, because the hot areas will overcure.
-
Change the filter
Remove the four screws and lift off the purifier box. The HEPA filter is the top layer and the carbon filter sits below it. Fit the new filter, then set the purifier back with its round connector socket facing the back of the oven and tighten the four screws.
-
Know when to stop
If the temperature keeps climbing past the set point, swings up and down, never reaches the setting, or the oven trips its breaker or won't power on, unplug it and contact us. Those point to the heater, controller or power supply, not your settings.
The Phoenix Air draws about 9 A. Don't run a heat press or other high-power equipment on the same circuit, and if you must use an extension cord, use one rated at least 16 A.
Check the cure
A cured sheet has a glossy, slightly bumpy orange-peel surface. Grainy or powdery means undercured: add time or heat in small steps. If peeling gets difficult after pressing, you may be overcuring; DTF Station's tests show film that has been cured too hot often can't be hot or warm peeled.
Text a photo of the cured sheet and your plate readings to (562) 609-4996.
Watch DTF Station's video: printing, powdering and curing with the Phoenix Air oven
Embedded from the manufacturer's official channel.
Common questions
What temperature and time should I use?
The Phoenix Air manual suggests 140°C (284°F) for 60 seconds. DTF Station's minimum for a full cure is 120°C (248°F), and Glide Pro film and Color Prime powder list 125°C (257°F) for 60 seconds. Start at the manual setting and adjust by the finish: glossy orange peel is cured, grainy is not.
Should the purifier be on while the oven heats up?
No. Turn it on only while a cure is running and off when you're done. Leaving it on for long periods can push the oven above your curing temperature, and it wears out the filter.
How often do I change the filter?
DTF Station now recommends replacing the HEPA and charcoal filter monthly. The oven's 2023 manual lists every 3 months for the HEPA filter and 6 to 9 months for the carbon filter. Change it sooner if smoke gets through.
Which replacement filter fits?
The DTF Station replacement filter for the Phoenix Air 16x20 and the original Miro 13. It does not fit the Miro 13 Max.
My sheet is burning or yellowing. Why?
It is getting too much heat or time. Lower the temperature or shorten the time, and measure the plate to make sure it isn't running hotter than the display shows.
- Phoenix Air 16x20 DTF Curing Oven user manual (PDF)
- DTF Station Phoenix Air 16x20 Curing Oven, product page
- Replacement Filter for Phoenix Air 16x20 and Miro 13, product page
- DTF Station: Prestige R1 basic operation with the Phoenix Air oven (video)
- DTF Station: Direct-to-Film Printing Safety Tips (video)
- Color Prime Quick Glide Pro DTF Film Rolls, product instructions
- DTF Station technical documentation
- AA and DTF Station support requests about Phoenix curing ovens, 2024 to 2026











































































