Support
Machine type
Brand
DTF Station Prestige A3+ and A3+ R

Not printing for a while? Idle and storage care for the Prestige R1, A3+ and A4

✓ Reviewed by Jason KimUpdated 2 min readFits: Prestige R1 · Prestige A3+ · Prestige A3+ R · Prestige A4
Short answer

On the R1, leave the printer powered on with the head capped: it cleans itself every 4 hours and circulates white every 15 minutes, as long as it has ink above 60% and no errors. Turn the heater and LED off and take the film out. On the A3+ and A4, do the full end-of-day clean, park the head on the cap, keep the printer level in a cool, dry room, and text us before a break of more than a few days so we can plan your restart.

Prestige R1: leave it on

The R1 is designed to look after itself while idle, but only while it's powered on, error-free and has ink. Before you leave:

  1. Fill the ink

    Top up so every ink level is above 60%.

  2. Set it up for idle time

    Turn the front heater off, the LED light off, and the ink alarm arm switch off. Set the white ink circulation knob to 20%.

  3. Take the film out

    Remove the film and store it in a cool, dry place.

  4. Clean and cap

    Do the full end-of-day clean around the head, wiper and cap, then press Enter to park the head and check it seals on the cap. Leave the printer on, with the cover closed and the dust cover over it.

While you're away, the R1 runs a light head cleaning every 4 hours and circulates white ink every 15 minutes on its own.

Prestige A3+, A3+ R and A4: clean, cap, and keep it cool

These printers don't have the R1's automatic white circulation, so time off is harder on them. Before any break of more than a day or two:

  1. Do the full end-of-day clean

    Clean the cap, wiper and around the print head with DTF cleaning solution, and make sure the head is parked and sealed on the cap. A head left off the cap dries out fast.

  2. Store it level, cool and dry

    Keep the printer level, out of the sun and away from heat. Epson, whose engine these printers use, warns that tilting or turning it on its side can make ink leak.

  3. Text us before a long break

    Before leaving it more than a few days, text us. Depending on how long you'll be gone and how much ink is in the system, we'll tell you what to do before you go and how to restart.

Coming back

  1. Wake up the white

    Shake the white ink bottle for 30 seconds. On the R1, stir the white tank if it's below half full.

  2. Run your morning routine

    On the R1, run a short Fill Ink and two head cleanings. On the A3+ and A4, check the waste bottle and dampers and run a head cleaning from DigiRip.

  3. Check before you print

    Print a nozzle check on film. On the R1, wait for 90% or better. If white or whole colors are missing after a couple of cleanings, follow the nozzle check guide for your printer rather than running cleaning after cleaning.

Text us a photo or short video at (562) 609-4996 if the nozzle check doesn't come back.

Watch DTF Station's video: Prestige closing procedure (end-of-day clean)

More videos

Changing the standby auto cleaning time on the Prestige R1
Prestige R1 beginning of day procedures

Embedded from the manufacturer's official channel.

Common questions

Should I turn the R1 off when I'm away?

No. Leave it on so it can run its own cleanings and keep the white ink moving. Turning it off lets the white settle.

How long can white ink sit without moving?

Not long. White is heavy and settles quickly. Printers that sit unused for days are the ones that come back with thin, see-through or dotty white.

Can I move the printer while it's full of ink?

Keep it level. Don't tip it on its side or upside down, or ink can leak. For the R1, refit the carriage L-bracket that came in the box before moving it any distance.

How should I store film and powder while I'm away?

Film in a cool, dry place out of the printer. Powder sealed airtight with a desiccant pack, away from heat, sun and moisture, and used within 6 months of opening.

Sources
Did this fix it?