Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R1 capping station error: station rises and falls on startup, error 4000 and the capping station sensor
Two capping station faults show up on the R1. In one, the station rises and falls over and over for about a minute after power-on. In the other, Pilot shows error 4000 (often with 13023), the carriage won't move and you hear grinding. The usual causes are firmware, the capping station sensor or its cable, the capping mechanism, or the motherboard. Send us a screenshot of the error codes and your firmware version first. A firmware reset from your backup fixes many cases, and a bad sensor is a one-screw swap.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Capping station rises and falls repeatedly for about a minute after power-on | Capping station sensor, or firmware | Steps 1, 2 and 5 |
| Error 4000 (often with 13023), carriage doesn't move, grinding at startup | Firmware, capping station sensor, its cable, the mechanism, or the motherboard | Steps 1 to 5 |
| Capping station rises but the carriage still won't move | Capping station sensor | Steps 3 to 5 |
Step by step
-
Send us the codes and firmware version
Open DTF Station Pilot, click the light bulb to open the Log and screenshot the error codes. Then go to Advanced > Firmware Version Model and screenshot that too. We'll check the firmware matches your printer's hardware before anything else.
-
Firmware reset from your backup
If the firmware is right, the next fix is re-importing your saved firmware files. This uses Pilot's protected Advanced menu, so we'll give you the steps on a call. If you have no backup, DTF Station's default firmware works but resets your settings: first photograph every value on the Calibration screens and in Ink Stack. Power the printer off and on afterward. If the cycling or error stops, you're done.
-
Free the carriage
With the printer off, turn the capping station knob to lower the station until the wiper clears the head and the head-strike sensor. Push the carriage by hand to the center of the bed and power on. If the capping station rises but the carriage still doesn't move, suspect the capping station sensor.
-
Reseat the sensor cable
With the printer off, go to the side of the printer and unplug the capping station sensor cable. Check the pins for ink residue, bends or damage, clean residue with a lint-free cloth and isopropyl alcohol, and plug it back in firmly. Power on and test.
-
Replace the sensor (once we've confirmed it)
DTF Station confirms a bad sensor either by unplugging its cable at the back or by swapping it with the identical carriage sensor, and we'll guide you through whichever fits. To replace it: move the carriage to the center (with the Left arrow, or by hand with the knob if the station keeps cycling) and turn the printer off. Remove the capping station cover (two screws at the top, two at the bottom) and open the side panel. Remove the single screw holding the sensor, lift it out and unplug it, peeling off any glue on the connector first. Plug the cable into the new sensor, set it in the same position, refit the screw and power on.
If the station keeps rising and falling with the sensor unplugged, or a new sensor doesn't fix it, the problem is the cable, the capping station or the motherboard. Stop there and contact us.
Keep a firmware backup
Most of this is quicker with a backup. Once your R1 is set up and printing well, and after any change, export both firmware backup files from Pilot (we'll show you how) and keep them in a folder outside your Desktop, named with the date.
Need help? Text us a photo or short video at (562) 609-4996 of the startup and screenshots of the Log.
Watch DTF Station's video: troubleshooting a capping station error on the Prestige R1
Embedded from the manufacturer's official channel.
Common questions
Should I keep restarting the printer to see if it clears?
Restart it once after the firmware step. If it still cycles or grinds, stop there and send us the codes rather than restarting it again and again.
I don't have a firmware backup. What happens?
We can send default firmware, but it resets your settings. Before importing it, photograph every Calibration and Ink Stack value in Pilot so they can be put back.
Which sensor do I order?
The DTF Station carriage and capping station sensor. The same sensor is used in both spots, which is how DTF Station tests which one is bad.
The sensor didn't fix it. What's next?
Then it's the sensor cable, the capping station itself, or the motherboard. Those jobs go into the back of the printer, so we'll walk you through them or arrange service.
How do I avoid losing my settings next time?
Export both firmware backup files from Pilot after setup and after any change, and keep them outside your Desktop folder.
- DTF Station: Prestige R1, how to troubleshoot a capping station error and replace the height sensor
- DTF Station: Prestige R1, how to troubleshoot capping station or motherboard error (error code 4000, 13023)
- DTF Station: Pilot, how to update motherboard and firmware (Prestige R1)
- DTF Station technical documentation
- AA and DTF Station support requests about capping station errors, 2024 to 2026










































































