Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R1 setup: unboxing, Pilot and NeoStampa, loading film and your first print
Unpack the R1 with two people, register the warranty within a week and keep the box and pallet. Assemble the media brackets and film rod level, remove the tape and the carriage bracket, and power on. Install Pilot on a Windows PC, connect the printer by Ethernet and set its IP in Pilot's network menu until the connection icon turns green. Then install NeoStampa with its USB dongle, load film, get a 90% nozzle check and print.
Before you start
- A Windows 11 PC: Intel i5 or i7 (2.6 GHz or faster), 8 GB of RAM or more, a 500 GB or larger SSD, and an Ethernet port
- A sturdy, level table in a room around 70 to 75°F, out of direct sun
- Two people to lift the printer (it weighs close to 90 lbs), screwdriver, Allen wrench set, scissors and a utility blade
- Your Quick Start Guide PDF, which links to the Pilot and NeoStampa downloads
Unbox and assemble
-
Inspect before opening
Check the box for damage first. If it's damaged, contact us before going further. Write down the serial number from the silver sticker on the box, and photograph the packaging as you open it. If anything is missing, stop and contact us.
Register your warranty within one week of delivery, and keep the original box and pallet for at least 6 months.
-
Lift it out with two people
Two people lift; a third slides the box away. Find the waste ink bottle in the bag of loose parts and test its alarm: press the alarm button and turn the bottle upside down.
-
Fit the media brackets and film rod
Attach the media brackets with the 16 medium Allen screws: line them up at the back with the legs flat on the table, start every screw loosely, then tighten evenly. Thread the film holder rod into the brackets, center it, and tighten the knobs without overtightening. Printer, brackets and rod must all be level, or the film will shift.
-
Remove tape and the carriage bracket
Remove all protective tape and film. Unlock and remove the L-bracket that holds the carriage, and keep it for transport.
-
Power on and test the panel
Plug in, switch on, and twist the red emergency stop to release it. The screen should show Initializing, then Idle, and the carriage should move slightly and return home. Press Left once to release the carriage, Enter to send it home, and Up/Down to move the pinch rollers.
Connect Pilot
-
Install Pilot
Download Pilot from your Quick Start Guide. Allow it through your antivirus or firewall, run the installer, and accept the Visual C++ installs.
-
Connect by Ethernet and set the IP
Plug the Ethernet cable into the right side of the printer and into the PC. In Pilot, go to Advanced > Admin Menu > Network, pick the Ethernet connection, and enter an IP that matches the printer's server IP except the last two digits (for example 192.168.127.xx). Don't use 10 as the last digits. Click Set, then OK, and wait 5 to 10 seconds. A green connection icon means you're connected. If it stays red, try another cable or adapter, or change the last two digits.
Set up NeoStampa
-
Install and activate
Install NeoStampa from the Quick Start Guide, plug in the USB dongle (its light must turn green), and register it with your details and the emailed code.
-
Add the printer
Choose Add > DTF Station, select the R1 driver, install it, and set the connection to TCP/IP Port.
-
Add the print modes
Download the schemes from the Quick Start Guide and unzip them somewhere safe. In a new DTG/DTF job, open the Scheme Manager, click Add, and select the .CPS file. Set your media width, and set the media color to RGB 105, 105, 105 so white areas of your art don't blend into the canvas.
Load film and print
-
Load the film
Wear gloves. The printable side is the outside of the roll. Mount the roll, center it with the bed and tighten the knobs. Raise the pinch rollers, feed the film under the metal rod, pull it forward and hold tension by pulling the roll back, then lower the pinch rollers. Slide the media guides in gently, just touching the edges.
-
Nozzle check and start position
Do the beginning-of-day routine and print a nozzle check from Pilot. Set the print start position (usually 40 to 60 mm when the film is centered). Don't print until the nozzle check is 90% or better.
-
Print, powder and cure
In NeoStampa, start a new job, add your files, nest them about 0.25 in apart, and print. Powder the film within 2 hours of printing, and cure at a minimum of 248°F (120°C), starting at 60 seconds and adjusting from there.
Stuck at any step? Text us a photo or short video at (562) 609-4996, or ask us about setup training.
Watch DTF Station's video: Prestige R1 assembly
Embedded from the manufacturer's official channel.
Common questions
Can I run the R1 from a Mac or a tablet?
No. Pilot runs on Windows only, not on a Mac, an iPad or a Surface tablet. Use a Windows 11 PC with an Ethernet port.
Can I connect it over Wi-Fi?
No. The R1 connects to the computer with an Ethernet cable plugged straight into the PC.
Pilot says "Failed to load parameters". What now?
The printer's motherboard or firmware needs an update. This is common on printers made before November 2024. Text us and we'll send the right package.
NeoStampa won't open. Why?
NeoStampa needs its USB dongle plugged in, with the dongle light green. If it isn't recognized, unplug every other USB device, restart the computer, and reopen NeoStampa.
Do I need to keep the box?
Yes. Keep the original box and pallet for at least 6 months, and save the carriage L-bracket for any future move.
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige R1 setup, 2024 to 2026











































































