Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro built-in cutter: Auto and Manual mode settings in Pilot
In DTF Station Pilot, open Settings > Cutter Settings. Set the Feed Value between 40 and 60 mm (50 mm is DTF Station's recommendation), choose Auto or Manual, and click Save. In Auto mode the printer feeds the film forward by the feed value and cuts as soon as the print finishes. In Manual mode it waits until you click Cut in Pilot.
Before you start
- Pilot is open and both icons are green.
- Film is loaded straight, with the media guides just covering the edges.
- You know whether you want each print cut on its own (Auto) or cut when you decide (Manual).
Auto mode: cut after every print
-
Open the cutter settings
In Pilot, go to Settings > Cutter Settings.
-
Set the feed value
Enter a Feed Value between 40 and 60 mm. DTF Station recommends 50 mm.
-
Choose Auto and save
Set Mode to Auto and click Save.
-
Print and catch the film
When the print finishes, the film moves forward by the feed value and the cutter fires on its own. The blade cuts from the center to the right, then from the center to the left. Hold the film so you catch the piece.
Manual mode: cut when you click
-
Choose Manual and save
In Settings > Cutter Settings, set Mode to Manual and click Save. Keep the feed value at 40 to 60 mm.
-
Print
When the job finishes, the printer stops and goes idle without cutting.
-
Cut from Pilot
Click Cut in Pilot, then OK. The film moves forward by the feed value and the blade cuts. Hold the film as it cuts.
Cutting by hand
If you need to cut without the cutter, or you have an original R2, pause or finish the job first. Use the Down arrow to move the film past the bed, hold it taut, cut straight across, and catch it before it separates. If the film creases, reload it.
Pause the job before you cut or adjust the film mid-run. Pulling on the film while the carriage is moving can lift it into the head.
If the cut goes wrong
- Film creased or pulled crooked after the cut: reload the film straight from the back and lower the pinch rollers again.
- Cutter doesn't fire in Auto mode: open Cutter Settings and confirm Auto was saved.
- Blade runs but doesn't cut cleanly, or the cutter makes an unusual noise: stop using it and text us a photo or short video at (562) 609-4996.
After the cut
Lay the cut sheet on the tray ink side up and cover the wet ink evenly with powder, then shake off the excess. Cure at 248°F (120°C) or higher; DTF Station's example is 257°F (125°C) for 60 seconds. A fully cured transfer has an orange-peel texture. If it looks grainy, give it more time or heat.
Questions about your cutter? Text us a photo or short video at (562) 609-4996 of what happens when it cuts.
Watch DTF Station's video: Prestige R2 Pro cutter operation
Embedded from the manufacturer's official channel.
Common questions
What does the feed value do?
It's how far the film moves forward after the print finishes before the blade cuts. DTF Station recommends 50 mm, within a 40 to 60 mm range.
Which mode should I use?
Auto cuts every job as soon as it finishes. Manual leaves the film uncut until you click Cut, so you can look at the print first.
Can I change the feed value later?
Yes. Open Settings > Cutter Settings, enter the new value within 40 to 60 mm and click Save.
Does the original Prestige R2 have the cutter?
This guide is for the R2 Pro, whose spec sheet lists a built-in sheet cutter. If you have an original R2, cut by hand as described below.
My R2 Pro runs Hosonsoft, not Pilot. Where is the setting?
These steps are for Pilot. Text us and we'll show you where it is in your software, or whether to upgrade.
- DTF Station: Prestige R2 Pro operation guide (cutter operation)
- DTF Station: Prestige R2 Pro spec sheet
- DTF Station technical documentation
- AA and DTF Station support requests about R2 Pro cutter setup, 2024 to 2026










































































