Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro setup: from the crate to your first print
Set up in this order: unbox and mount the feed system, remove the transport tape and carriage lock, fill the inks to 40 to 50%, switch on white circulation, run the first ink charge for at least 2 minutes, load film, install Pilot and connect by Ethernet, align the heads, then install NeoStampa with its dongle. DTF Station's Quick Start Guide has a video for every step. Keep the box, the carriage lock bracket and the yellow dongle packaging.
Before you start
- Tools: Allen keys, a snap blade, a Phillips screwdriver, scissors, a full set of ink and a roll of DTF film.
- Two people to lift the printer onto a sturdy table.
- A Windows PC that meets the requirements in the questions below, with an Ethernet port or adapter.
- The Quick Start Guide PDF from the USB drive or your dealer email. Every step below has a matching video in it.
Setup in order
-
Unbox and keep the packaging
Check the accessories: power cord, dampers, ink filters and tubes, ink diverter, ribbon cables, screws, two feed roller parts, and the USB dongle. Keep the box and put spare parts back in it. Never throw away the yellow dongle packaging.
-
Mount the feed system and film roll
Bolt the feed system to the back of the printer: start all eight bolts loosely, then tighten them. Slide the two feed roller parts onto the rods, center them and tighten the four knobs. Load the film printing side up, pushed against the left bracket and lined up with the left edge of the rear opening.
-
Remove transport tape and the carriage lock
Peel off the tape on the front and the printer bed and the plastic lining near the rail. Unscrew the carriage lock bracket above the bed, keep it with the box for any future move, and put its bolts back into the carriage.
-
Fill the inks
Shake each color for 5 to 10 seconds and the white for 15 to 20 seconds, then let the white rest at least 5 minutes. Fill each container with its labeled color to about 40 to 50%. Tighten each cap, then loosen it a quarter turn so air can get in. Watch the tubes while you fill: if ink runs toward the print head, clamp that tube immediately and contact us.
-
Power on and start white circulation
Switch on at the rear and check the Emergency Stop is released. In the right side panel, turn the white ink circulation knob fully clockwise until it clicks.
-
First ink charge
Press Menu, Down three times to Head Maintenance, Enter, Down twice to Fill Ink, Enter, leave it on Two Head and press Enter. Let it run at least 2 minutes, then Cancel. Run one head cleaning, and two more once the status returns to Idle.
-
Waste tank, film and alarms
Put the waste tank on the floor or anywhere lower than the printer and press its button to turn on the alarm. Feed the film under the guide bar, lift the roller handle, pull the roll taut and straight, and lower the handle. Bring the media guides in to just cover the film. Switch on the ink alarm, then turn the circulation knob counterclockwise halfway.
-
Install Pilot and connect
Download Pilot from the Quick Start Guide, allow it through your antivirus, and connect the Ethernet cable straight to the printer. Pick the right network adapter and IP address as in our connection guide. Match the settings shown in the setup video, leave spot color unchecked, and set the print start position (typically 50 to 70 mm with the film centered).
-
Align the heads
With at least 90% of nozzles firing, run the step, head and bidirectional adjustments exactly as the setup video shows. On the R2 Pro you adjust only the white head (H2), never the color head. Then export both firmware backup files and keep them somewhere safe. Skip calibration if a technician did your on-site setup.
-
Install NeoStampa
Install NeoStampa, activate the dongle and import your print schemes. See our NeoStampa install guide.
-
Make your first transfer
Print a nozzle check, then your job. Powder the wet ink evenly and shake off the excess. Cure at 248°F (120°C) or higher until the surface looks like orange peel, not grainy. Press at 320°F (160°C) for 15 seconds at medium pressure.
Stuck on a step? Text us a photo or short video at (562) 609-4996 of the screen or the printer.
Watch DTF Station's introduction to the Quick Start Guide
Embedded from the manufacturer's official channel.
Common questions
What computer do I need?
A Windows 11 PC with an Intel i5 or i7 at 2.6 GHz or faster, at least 8 GB of RAM and 500 GB free (an SSD is better), plus an Ethernet port or adapter. No Mac or tablet, and a Surface Pro counts as a tablet.
Where do I get the software and the Quick Start Guide PDF?
On the USB drive that came with the printer, or from the link in your dealer email. If you can't find either, contact us and we'll resend it.
Do I need an activation code?
Not for the R2 Pro. NeoStampa is licensed by the USB dongle in the bright yellow IMPORTANT packaging. Keep it safe: without it you can't print.
My printer was built before December 2024. Anything different?
It may need a motherboard and firmware update before current Pilot will work. Check the date on the serial number sticker and ask us before installing Pilot.
Do I have to redo the head alignment later?
Yes, whenever you switch to film of a different thickness or replace a print head.
- DTF Station Prestige R2 Pro Quick Start Guide
- DTF Station Prestige R2 Pro user manual
- DTF Station Prestige R2 Pro Operation Guide
- DTF Station: Prestige R2, DTF general troubleshooting (curing and pressing)
- DTF Station technical documentation
- AA and DTF Station support requests about R2 Pro setup, 2024 to 2026










































































