Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige DTF printer white ink not printing or weak underbase: A3+, A4 and R1 fixes
First print a nozzle check on film. If the white rows are missing, it's the ink or the head: shake or stir the white, check the white dampers and lines, and on the R1 keep the circulation knob at 20%. If the nozzle check is complete but the white looks thin on the transfer, it's a setting: raise the white amount in DigiRip or NeoStampa in small steps. Hot, dry rooms and fans blowing on the printer also make white drop out.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| White rows missing or broken on the nozzle check | Settled white, clogged white nozzles, or a white damper or line | Ink and head |
| Nozzle check complete, but white is thin or see-through on the transfer | White amount set too low for the job | RIP settings |
| White is good in the morning, fades during a run | Air blowing on the head, a hot and dry room, or a head strike | The room |
| White prints gray or dark (R1) | Color ink got into the white line after an ink fill | Ink and head, step 2 |
| Thin white halo or white peeking past the edges | Not enough choke, or white set too high | RIP settings |
Ink and head
-
Get the white moving
White ink is heavy and settles. Shake the white bottle for about 30 seconds every morning. On the A3+ and A4, the white bottle with the built-in stirring system helps keep it mixed. On the R1, also stir the white tank once a month with the stirrer, but only when it's below half full, and rinse the stirrer with distilled water afterward.
-
R1: check the white circulation knob
Keep white circulation at 20%. You should barely hear the pump. Too high pulls ink out of the dampers and makes bubbles in the white line. After any Fill Ink, always turn it back to 20% or lower, or color can leak into the white.
-
Clean, then check the nozzles again
Run your normal head cleaning and print a nozzle check on film. If only white is missing, run one more cleaning. If it still won't come back, check the white dampers next.
-
Check the white dampers and lines
Look for a long air gap in the white tube above the dampers and make sure each damper is fully seated. Dampers wear out and should be replaced about once a year. On the R1, both white dampers share one ink system: if both seem to fail at once, the dampers probably aren't the cause. Send us a video before replacing them.
RIP settings
Only change settings once the nozzle check is complete. Move in small steps and print a test each time.
- DigiRip (A3+, A4): for every new job, open Queue Properties > Color Layer > Processing Options. For one image only, double-click the image and open the same tab. Maximum White Ink Percentage defaults to 60%: change it in 10% steps. Make sure Underbase is selected. If white shows past the edges, raise the choke.
- NeoStampa (R1): for one image, select it and open White Effect Layer > Flat Method, then adjust Intensity. For everything, use the three-dot icon, open your profile, and adjust Intensity under the White Ink icon. Use the choke setting in the same menu if white peeks out at the edges.
- Pilot (R1): Settings > Global Ink Setting can double the white for dark garments. It doubles ink use and halves speed, so leave it off unless a job really needs it.
The room
Hot weather and dry air are hard on white. Aim for 70 to 75°F and 35 to 45% humidity, and make sure no fan, heater or AC vent blows across the printer. Also ask yourself whether the head has touched the film recently: residue from a head strike can slowly block white nozzles weeks later.
Still stuck? Text us a photo or short video at (562) 609-4996, with a nozzle check photo and a photo of the transfer.
Watch DTF Station's video: getting better whites on the Prestige A3+ R
More videos
Embedded from the manufacturer's official channel.
Common questions
How do I see white on a nozzle check?
Print it on DTF film and hold it over something dark. White never shows on white paper.
My white looks gray or dark after I filled ink on the R1. What happened?
During setup the white circulation runs at 100% for a while. If the knob isn't turned back to 20% or below afterward, color ink can get into the white line. Turn it down. If the white stays dark, contact us and we'll walk you through draining the line.
Should I just turn the white up to 100%?
No. Change it in 10% steps and test. Too much white causes bleeding, white showing past the edges, and a heavier transfer.
White is fine at the start of the day but fades after a few prints. Why?
Look for air blowing on the printer from a fan or AC vent, and a hot, dry room. White is heavier than the colors and dries in the nozzles first. Also check for any time the head touched the film.
How long does white ink last once it's in the printer?
It needs to keep moving. Leaving the printer off for days lets the white settle, which leads to thin, spotty white. On the R1, leave it powered on so it can circulate on its own.
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige white ink, 2024 to 2026











































































