Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige X6 installation: site requirements, stand assembly and transport locks
The X6 must be unloaded and installed by trained people: six or more to lift it, or a forklift using the two brackets under the printer body. Put it indoors on a level, vibration-free floor in a ventilated room held at 68 to 83°F and 40 to 60% humidity. Before the first power-on, remove every transport lock and the carriage fixing blocks, and keep them for any future move.
Before delivery
- People: unloading and installation must be done by trained, qualified people. Lifting the printer takes six or more people, or a forklift using the two brackets under the printer body.
- Floor: level, stable and free of vibration, indoors only.
- Air: a ventilated room (ink gives off vapors), away from flammable materials and combustible gases.
- Power: the plug must stay easy to reach. Keep the printer away from electrical noise and magnetic interference.
- Avoid: direct sunlight, air conditioning and heaters, water or moisture, dust, strong airflow, sloped floors, and rooms with big swings in temperature or humidity.
| Temperature | Humidity | |
|---|---|---|
| While printing | 68 to 83°F (20 to 28°C) | 40 to 60%, no condensation |
| While idle | 59 to 86°F (15 to 30°C) | 30 to 80%, no condensation |
The machine measures about 2535 x 1200 x 1605 mm. Allow about 3530 x 2200 mm to install it and 4530 x 3200 mm to work around it.
Check the stand kit
Lay everything out against the accessories list before you start. You should have the support leg bases and legs, reinforcement plates, slide-rail fixing plates, the rear tension bar and tension bars with brackets, two take-up reels, the ink bottle holder, waste ink holder, PC plate, keyboard tray and display arm. The box also holds a USB drive, a print head cable, the power cord, a damper, screw packs and tube connectors. Contact us if anything is missing.
Assembly points to get right
-
Legs
The L marking must face the same way on the leg and its base. Leave the screws loose until the bottom screws are in, then tighten them all.
-
Reinforcement plates
Each plate must sit parallel to the leg and completely flush. Any gap gets in the way when the printer body goes on.
-
Slide-rail fixing plates
Remove the slide-rail stopper plate first, then fit the fixing plate. The rear tension bar must slide up and down smoothly. Refit the stopper plate and check that the tension bar bearing stays inside it without touching. Readjust if it touches.
-
Printer body
Lift it on with six or more people or a forklift, secure it, then add the bottom beam reinforcement plates.
-
Media holders and take-up reels
The media holder switches face outward. The open side of each take-up reel faces the back, so slide the front side onto the shafts first.
-
Waste and ink
Put the waste ink tube into the waste bottle after mounting its holder. Connect each ink tube to its bottle by matching the tube code and the color label.
Remove the transport locks before first power-on
Open the front cover and remove the carriage fixing blocks and every other transport lock. Peel the protective stickers off the media guides and slide the guides to both sides of the platen.
Powering on with any transport lock still fitted can damage the printer. Keep all the locks: you need them again whenever the X6 is moved.
For first ink fill and software setup, wait for your technician or text us at (562) 609-4996.
Common questions
How much room does the X6 need?
The machine is about 2.5 m long, 1.2 m wide and 1.6 m high. DTF Station recommends about 3.5 x 2.2 m for installation and about 4.5 x 3.2 m of operating space.
Does the room need to stay within range when the printer is off?
Yes. Idle limits are 59 to 86°F and 30 to 80% humidity, with no condensation, and should be kept even when you aren't printing.
What happens if I power on with the transport locks in?
It can damage the printer at startup. Remove all of them first, including the carriage fixing blocks under the front cover.
Should I throw the transport locks away?
No. Keep them. They are needed again any time the printer is relocated or shipped.
What paperwork comes in the box?
An accessories list, a stand assembly guide, a user's manual and safety instructions, plus a USB drive.
- DTF Station technical documentation
- AA support requests about Prestige X6 setup, 2025 to 2026











































































