Support
Machine type
Brand
Phoenix Air 16x20 DTF Curing Oven

Seismo S20 DTF powder station: setup, shaking speed, powder drop and cleaning

✓ Reviewed by Jason KimUpdated 2 min readFits: Seismo S20 (GS-401)
Short answer

The Seismo S20 powders printed DTF sheets up to 16 x 20 in and shakes off the excess, then you cure the sheet in an oven such as the Phoenix Air. Fill the powder box so the bottom is evenly covered (about 4 kg maximum), switch on shaking at about 1500 RPM, and push the press plate down about three times to cover the film. Unplug it and cover the powder box after every session.

The S20 is a manual powder station. You lay a freshly printed sheet in it, drop powder over the print, and a motor shakes the sheet so the loose powder falls away. It runs on 110 V and draws very little power. Curing happens afterward in your oven, which is why most shops pair it with the Phoenix Air 16x20.

Assemble it

  1. Mount the control box

    Attach the control box with its screws.

  2. Connect the aviation plug

    Line the aviation plug up with the socket in the correct position, push it all the way in, then screw the collar on tight. A loose or crooked aviation plug is the first thing to check if the S20 stops or shows an error.

  3. Fit the drawer handle

    Attach the handle to the drawer with the M5 screws, tighten them firmly, and slide the drawer into the machine.

Fill and position

  1. Fill the powder box

    Lift the lid and pour powder in so the bottom of the box is evenly covered. The box holds about 4 kg.

  2. Place the film

    Use the A3 jig for A3 sheets, or the 40 x 50 cm slot for 16 x 20 in sheets, so the print sits square under the powder drop.

Run it

  1. Power

    Push the power cord into the socket on the control box and switch on. The power light should come on.

  2. Start shaking

    Press the shaking On/Off button. The display shows the motor speed. Adjust it with the speed buttons. About 1500 RPM suits most work.

  3. Drop the powder

    With the motor shaking, push the press plate down. Powder drops at once. About three pushes is usually enough to cover the print.

  4. Cure

    Move the sheet to your oven and cure it. See DTF powder curing temperature and time.

Clean and store it

  • Switch the power off and pull the power cord out after every use.
  • Close the powder box lid and put the dust cover over the machine so powder doesn't pick up moisture or dust.
  • Brush loose powder out of the station. Store the powder separately in a sealed container, and DTF Station suggests adding silica gel packs to keep it dry.
  • Wipe powder dust off the outside with a lint-free or microfiber cloth.

If the display flashes an error, the motor starts and then stops, a spring breaks, or you find a wire you can't place in the instructions, stop and don't guess. Text us a photo or short video at (562) 609-4996 and we'll tell you what it is.

Watch DTF Station's video: Seismo S20 basic operation

More videos

Introducing the Seismo S20 powder station

Embedded from the manufacturer's official channel.

Common questions

What speed should I run the S20 at?

The manual says about 1500 RPM is right for most jobs. A higher number on the display means a faster motor.

How much powder does it hold?

About 4 kg. Spread it so the bottom of the box is evenly covered.

How many times do I push the press plate?

About three pushes usually covers the film. Push more if you see bare spots.

Does the S20 cure the powder?

No. It only applies and shakes off powder. Cure the sheet afterward in an oven or conveyor dryer, such as the Phoenix Air 16x20.

What sheet sizes fit?

A3 sheets sit in the A3 jig, and 16 x 20 in (40 x 50 cm) sheets sit in the 40 x 50 cm slot.

Sources
Did this fix it?