Support
Machine type
Brand
STS VJ-628D DTF Printer (Mutoh)

STS VJ-628D clogged nozzles or no white ink: the cleaning order that works

✓ Reviewed by Jason KimUpdated 2 min readFits: VJ-628D · VJ-628D-C
Short answer

Shake the white ink first, then print a nozzle check. Run Normal cleaning a few times, then Long cleaning a few times. If gaps remain, clean the wiper and around the print head with a dry cleaning stick, and only then use Little Charge, which uses a lot of ink. If 4 or 5 cleanings in a row don't help, stop and wet cap overnight instead of cleaning more.

Match your symptom

What you see Most likely cause Start at
White channels blank or patchy on the nozzle check Settled white ink, or a partial clog Step 1
A few gaps in one color Partial clog Step 2
Gaps across every channel right after a film jam Head strike Our head strike guide
Clean check in the morning but bad after sitting idle for days Printer left without Long Store Step 5, then our Long Store guide
White ink dripping from the head, or air visible in a white line Possible ink supply or damper problem Stop and contact us

Step by step

  1. Shake the white ink

    Lay each white cartridge flat and shake side to side for 2 minutes, or massage 1 liter bags while shaking. Reseat them fully. Settled white is the most common reason white looks weak.

  2. Normal cleaning, then check

    In the driver choose Utility > Cleaning, select Normal and click Start. Print a nozzle check. Repeat a few times if the gaps are shrinking.

  3. Long cleaning, then check

    If Normal hasn't cleared it after several tries, switch to Long. It uses more ink than Normal. Repeat with a nozzle check after each one.

  4. Clean the wiper and around the head

    If Long cleaning hasn't worked after several tries, the STS manual says to clean the cleaning wiper and the head surroundings next. Use CR Maintenance to bring the carriage forward and wipe with a dry, new cleaning stick. Never touch the nozzle surface.

  5. Little Charge

    Only after the steps above, run Little Charge. It cleans harder than Long and uses a large amount of ink, so check your waste tank first.

  6. Stop and wet cap

    If 4 or 5 cleanings haven't helped, stop cleaning. STS warns that sustained cleanings put pressure on the head and can cause early failure. Fill the capping station with STS cleaning solution, park the head on it, turn the printer off and leave it overnight. Next morning, shake the white and print a nozzle check.

Don't open the printer housing to work on tubes or dampers. STS says opening the casing voids the warranty, and its warranty excludes damage from service by anyone other than STS or an approved supplier.

Before you contact us

Have a photo of your latest nozzle check and our printhead checklist answers ready. It lets us and STS diagnose it in one conversation instead of several.

Watch STS Inks' video: wet capping the 628 and 724 after a head strike

More videos

STS Inks: why shaking your white ink matters
STS Inks: shaking the whites before waking the printer

Embedded from the manufacturer's official channel.

Common questions

Why does my nozzle check sometimes get worse after a cleaning?

Don't answer it with more cleanings back to back. STS warns that sustained cleanings stress the head. If checks keep getting worse, stop, wet cap overnight, and send us the before and after nozzle check photos.

My white fades partway through a print but the nozzle check looked fine.

Start with the basics STS lists: shake the white thoroughly, and check that the white cartridge or bag sits fully in its slot. If it continues, send us a photo of the print and the nozzle check.

MSM gives an S/C card error or won't read a new cartridge.

Make sure each cartridge has its own matching card installed and that the color matches the slot label. Don't swap cartridges with the printer off, since the printer can't track ink levels then. If the error stays, contact us with the cartridge batch number.

Is Little Charge safe to run every day?

STS lists Little Charge as the strongest cleaning and warns it uses a large amount of ink. Use it after Normal and Long have failed, not as a daily routine.

Sources
Did this fix it?