Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS VJ-628D head strike: how to prevent it and what to do right after
A head strike happens when the film lifts, wrinkles or goes slack and touches the print head. DTF film's coating gels any ink it touches, so a strike can block nozzles fast. Prevent it by loading the roll tight with no slack, setting the paper guides, keeping the front cover down and never touching the film while printing. If it happens, stop, clear the film, then run cleanings and nozzle checks. If 4 or 5 cleanings don't recover it, wet cap overnight.
Why a head strike is so serious on a DTF printer
DTF film is coated with an emulsion that sets ink into a gel the moment it lands. If the print head touches the film, any ink on the head surface gels too, right across the nozzles. That is why one strike can wipe out several channels, and why repeated strikes shorten the life of the head.
Prevent it
-
Load the roll tight, with no gap and no slack
Push the roll against the fixed media stopper on the scroller, then push the movable stopper in until there is no gap. After you feed the film through, rewind the scroller if the film is loose. Lock the media fixing knob, then slide the paper guides in from both sides of the platen.
-
Use flat, undamaged film
Don't load film that is folded, scratched, curled or wavy. After opening a new roll, let it sit about 30 minutes to adjust to the room. Don't leave a roll in the printer for long periods, because it curls.
-
Check the roll before long jobs
Make sure there is enough film left on the roll for the job before you send it.
-
Keep hands off while it prints
Always print with the front cover down. Don't lift or touch the film while the printer is running, including when you are feeding it into a shaker.
-
Adjust for film that lifts or wrinkles
If heavy ink coverage makes the film lift, set the head height lever to High, then run the image quality adjustment. If thin film wrinkles, set the vacuum fan to Middle or Low in the driver (Basic > Advanced) or MSM, or release the pressure arms at both edges and then redo the paper feed correction.
If the head hits the film
Do not keep printing to see if it clears. Every pass over gelled ink makes it worse.
-
Stop the job
Hold the operation key for 2 seconds or more to cancel printing.
-
Clear the film
Turn the printer off, open the front cover and remove the jammed or wrinkled film. Cut it free rather than pulling it under the head. If the carriage will not move freely or film is wrapped around the head area, stop and contact us before forcing anything.
-
Reload and power on
Reload the film the way described above, close the front cover and turn the printer on.
-
Clean and check, one at a time
Start a head cleaning from MSM, then print a nozzle check. Repeat until the pattern has no gaps.
-
Wet cap overnight if it isn't recovering
If the nozzle check is still poor after 4 or 5 cleanings, fill the capping station with STS cleaning solution, park the head on the capping station, turn the printer off and leave it overnight. The next day, shake the white ink as usual and print a nozzle check.
-
Still missing nozzles?
STS suggests printing in high quality (720 x 1440) or with double white as a temporary workaround. Then send us your nozzle check photos so we can look at it with STS.
Watch STS Inks' video: what to do after a head strike on the 628 and 724
Embedded from the manufacturer's official channel.
Common questions
Is a head strike covered by warranty?
STS states it will not warranty head damage caused by operator error, and its warranty excludes media jams that aren't caused by a manufacturing defect. That is why prevention matters so much on this printer.
How many cleanings should I run after a strike?
Run a cleaning, then a nozzle check, and repeat. If the pattern is still poor after 4 or 5 cleanings, stop and wet cap overnight. STS warns that nonstop cleanings put pressure on the head and can make it fail early.
The whole nozzle check is bad on every channel right after the film jammed. What does that mean?
Damage across every channel at once, right after a jam, points to a strike rather than a normal clog. Send us a photo of the nozzle check and tell us what happened.
Can I raise the head so it doesn't touch the film?
The VJ-628D has a Low and High head height lever under the front cover. STS's manual suggests High when media lifts or rubs. Never change it while printing, and run the image quality adjustment in MSM after you change it.
Can I park the head on the film overnight?
No. STS says never park the head directly on PET film. Park it on the capping station.
- STS/Mutoh 628D Printer Guidelines (STS Inks best practices)
- STS VJ-628D Operations Manual 2.0
- STS VJ-628D Limited Warranty (US)
- AA help center: STS head strike notes (2021), verified against STS documents
- AA support requests about STS head strikes, 2024 to 2026











































































