Support
Machine type
Brand
STS VJ-628D DTF Printer (Mutoh)

STS VJ-628D printhead problem? Checklist before you contact support

✓ Reviewed by Jason KimUpdated 2 min readFits: VJ-628D · VJ-628D-C
Short answer

Before you report a printhead problem, print a nozzle check and photograph it, note when the problem started, list the cleanings and maintenance you have done, check the room temperature and humidity, and write down your white ink batch number. Send it all to us together. Whether all channels or only some are affected tells us a lot about the cause.

Gather this first

  1. A nozzle check photo

    Print a nozzle check from Utility > Nozzle Check and take a clear, well lit photo. If you have run cleanings, include the check from before and after.

  2. Which channels are affected

    Is it one color, the two white channels, or every channel at once? Problems across every channel, especially right after a film jam, point to a head strike. One or two channels point to a clog or an ink supply issue.

  3. When it started

    Note the date, and anything that happened just before: a jam, a power outage, a new box of ink, a few days without printing, a move.

  4. Maintenance you've done

    List the cleanings you've run (Normal, Long, Little Charge, how many of each), and when you last cleaned the wiper, the area around the head and the capping station, and whether you wet capped.

  5. Room conditions

    Check the temperature and humidity where the printer sits. The STS manual calls for 68 to 75 °F and 45 to 55% humidity.

  6. Ink details

    Write down the white ink batch number and expiry date, and whether you use cartridges or 1 liter bags. STS says not to use expired ink.

  7. Your serial number and proof of purchase

    STS needs the serial number, purchase date and place of purchase for any warranty review.

Quick checks that often solve it

  • Shake the white ink for 2 minutes, flat, then print a new check.
  • Make sure every cartridge is fully seated, matches its slot label and has its matching card installed.
  • Look at the bottom of the head area for ink lumps or fibers, and clean around the head with a dry cleaning stick.
  • If the printer has been sitting, see our Long Store and restart guide.

Stop and contact us right away if

  • Ink is dripping from the head or leaking from a cartridge.
  • Both lights on the panel flash together and the buzzer sounds at intervals. That is emergency mode. Turn the printer off, wait at least 10 seconds and turn it on. If it comes back, it needs a technician.
  • MSM shows a message about print head or motor life.

What happens next

We review your photos and answers, and may ask you to run one more nozzle check or a specific cleaning so we can see how the head responds. If it looks like a part or warranty issue, we pass the full picture to STS so you don't have to repeat yourself. In the meantime, avoid running cleaning after cleaning. STS warns that sustained cleanings put pressure on the head and can make it fail early.

Text us your photos and answers at (562) 609-4996, or contact us, and we'll take it from there with STS.

Watch STS Inks' video: wet capping the 628 and 724 after a head strike

Embedded from the manufacturer's official channel.

Common questions

Who handles warranty on an STS printer, AA or STS?

STS's warranty says your first contact is the place you bought it. We gather the details and work with STS. You'll need your proof of purchase showing the date, place of purchase and serial number.

How long is the printhead covered?

STS's US limited warranty lists 1 year for the VJ-628D (excluding the printhead) and 6 months for the DX7 printhead, from the date of purchase, for the original purchaser.

What isn't covered?

Among STS's listed exclusions: non-STS ink, parts or media, consumables bought from an unauthorized dealer, media jams not caused by a defect, unsuitable environment or power surges, service by anyone other than STS or an approved supplier, and failure to clean and maintain the printer as described in the user guide. STS also says head damage from operator error is not covered.

Can I replace a damper myself?

Damper replacement means disconnecting ink tubes at the print head. STS says not to open the printer housing and excludes damage from unapproved service, so contact us first.

Sources
Did this fix it?