Support
Machine type
Brand
Uninet iColor white toner transfer printers (560, 650, 800W and earlier models)

Uninet iColor printer not connecting or not printing from ProRIP: network, Wi-Fi and port setup

✓ Reviewed by Jason KimUpdated 2 min readFits: iColor 560 · 650 · 800W · 550 · 600
Short answer

If ProRIP shows 'Port Failed to Open', leaves jobs on Holding, or opens a Save File box when you click Print, the queue isn't pointed at your printer. Open Queue > Manage Queues and set the Port to TCP/IP (network) or to the USB port named for your iColor printer. Give the printer a static IP address so it doesn't change, and never connect USB and network cables at the same time.

Match your symptom

What you see Most likely cause Go to
'Port Failed to Open' error Queue port not set, or the printer's IP address changed Steps 2 and 3
Job sits on 'Holding' Queue port not set Step 2
A Save File box opens when you click Print Queue is set to print to file instead of the printer Step 2
ProRIP can't find the printer on the network Cable, Wi-Fi or IP problem Steps 1 and 3
Worked, then stopped after the printer was off for a while The router gave the printer a new IP address Step 3

Step by step

  1. Check the physical connection

    On the 560 the ports are under the side panel. Use either the USB cable or the network cable, never both at once. If you're using Wi-Fi, unplug both cables. Power the printer on and wait until it's ready.

  2. Point the queue at the printer

    In ProRIP (the dongle version used on the 650, 800W and earlier 560s), go to Queue > Manage Queues. In the Port column, choose TCP/IP for a network printer and pick your iColor from the list ProRIP finds, or choose the USB port that has your printer's name in it. Don't pick a generic port such as Printer_USB-001+. You only need to set it on one queue: the others follow. Port settings can reset when the queues update, so check here first whenever this error comes back.

    In ProRIP Essentials (newer 560s), choose your printer under Output Destination. If it's set to File, the software saves a file instead of printing.

  3. Give the printer a static IP address

    Without one, your router can hand the printer a new address after it's been off, and the queue loses it. On the 560: press Menu, go to Network Settings > IPv4 Configuration > DHCP and set it to Inactive. Then set IP Address, subnet mask and default gateway in the same menu. Use an address your network allows: whoever manages your router can give you one. Then repeat step 2 so the queue uses the new address. On other models, the static IP menu is in that model's user manual.

  4. Setting up Wi-Fi on the 560

    Unplug the network cable. Press Menu, go to Network Settings > Wireless (Wi-Fi), set it to Enable, and restart the printer. Then press Menu, open Wi-Fi Setup Wizard, choose your network name and enter its password. Check Wi-Fi Status shows Connected. You can also use your router's WPS button: choose WPS > PBC on the printer and press the router's WPS button within two minutes. Then set the port in ProRIP as in step 2.

  5. No network at all? Use Wi-Fi Direct

    The 560 can make its own wireless link to one computer. Disconnect the printer and the computer from other networks, press the printer's Wi-Fi Direct key, and connect the computer to the network named DIRECT- followed by letters and numbers, using the key in your user manual.

  6. Print a test page

    In ProRIP, choose Devices > Print Test Page to confirm everything is connected before you load transfer paper.

Don't set an administrator password or change other settings on the printer's control panel. Uninet says this can lock you out permanently and isn't covered by the warranty.

Still not printing?

Send us a photo of the ProRIP error and of the printer's screen at (562) 609-4996, and tell us your model, how it's connected and whether it ever worked on this computer.

Common questions

Should I use USB or network?

Uninet recommends a network connection for the most reliable and fastest printing. Use one or the other: never plug in USB and network at the same time.

It worked yesterday and today it says Port Failed to Open.

The printer's IP address has probably changed, or updating the queues reset the port. Set the port again under Queue > Manage Queues, and give the printer a static IP so it stops happening.

Do I need to install the Windows printer driver?

Not to print from ProRIP. The 560's Windows driver is optional and only for printing without white, outside the RIP.

Can I change settings on the printer's screen to fix it?

Only the network settings shown here. Uninet asks you not to change other control panel settings, and never to set an administrator password, unless their technician tells you to. A forgotten password can make the printer unusable and isn't covered by the warranty.

My antivirus flagged ProRIP. Does that matter?

Yes. Uninet says third-party antivirus can delete RIP files and cause print and connection problems. Remove it or add ProRIP to its safe list. Windows Defender is the only one Uninet says doesn't conflict.

Did this fix it?