Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
iColor 2-step transfer paper not sticking: adhesive not transferring or image not adhering to the shirt
Most 2-step failures come from a press that isn't hot enough on the bottom, thin toner coverage, damp adhesive sheets, or peeling at the wrong time. Preheat the press closed for at least 5 minutes, print with the white overprint from ProRIP so coverage stays above 70%, peel the adhesive sheet hot, and peel the transfer sheet off the garment only once it's completely cool. Use the exact temperature and time on your paper's own instruction sheet, because each iColor paper is different.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Adhesive didn't cover the whole print, gaps or holes | Lower platen not hot, thin toner coverage, or damp adhesive sheet | Steps 1, 2 and 4 |
| Parts of the design stayed on the adhesive sheet | Peeled too slowly or too cool, or a dense dark image needs more heat | Step 3 |
| Image won't stay on the garment when peeling | Peeled while warm, or the wrong temperature for the fabric | Step 5 |
| Sheets crinkle or buckle after laminating | Humidity in the media | Step 4 |
| Image washes out or cracks | Re-press skipped, or no stretch after re-press | Step 6 |
Settings differ by paper
| Step | iColor Premium 2 Step | iColor Select 2 Step |
|---|---|---|
| Print side | Smooth, coated side | Rough, coated side |
| Marry A and B | Laminate first, then 250°F, 30 s, medium-high pressure, under kraft paper or a PTFE sheet | 310°F, 120 s, medium-high pressure, under kraft paper or a marrying cloth. Not PTFE. |
| Peel adhesive sheet | Hot, diagonally, one quick motion | Hot, rub 5 s with fabric, then peel slow and low |
| Press onto cotton | 250°F, 30 s, medium-high | 310°F, 25 s, high (285°F on 50/50, 265°F on polyester) |
| Re-press | About 25 s at 250°F under kraft paper | 265°F for 30 s, heavy pressure, or 310°F for only 10 s |
Standard, Ultra Bright and other iColor papers have their own sheets. Use the one for your paper: mixing settings between papers is a common cause of failures.
Step by step
-
Preheat the bottom of the press
Close the press at the marrying temperature for at least 5 minutes before the first marry. Uninet calls this extremely important: don't start until you can feel heat coming up from the lower platen, or the adhesive won't fully transfer.
-
Print with the right mode and enough toner
In ProRIP, use the overprint queue and the print mode named for your paper (for example 'UNINET IColor 2 Step Premium'), with the matching page size. Mirror the image if the RIP doesn't. Toner coverage below about 70% leaves too little for the adhesive to grab, so let ProRIP add the white overprint, even for white garments.
-
Marry and peel while hot
Put the printed sheet face up and the adhesive sheet face down on top, adhesive to image. Fold a small corner of the adhesive sheet over to make peeling easier. Press, then peel right away on the press so it doesn't cool. Start from the area with the most toner. Afterward, check the used adhesive sheet: if any of your design is on it, the pull wasn't clean. For Select paper with a lot of dark or black, Uninet allows 340°F for 135 seconds.
-
Dry out damp adhesive sheets
If you see gaps in the adhesive, or the sheets crinkle after laminating, the adhesive sheets have absorbed moisture. Lay them face up on the hot lower platen for 1 to 2 minutes without pressing. Store them sealed with a silica pack. Uninet's ideal room is 45 to 65% humidity and 50 to 75°F.
-
Press onto the garment and peel cold
Trim the transfer close to the design so no adhesive box shows. Tape it print side down with heat-resistant tape, cover with kraft paper or a PTFE sheet and press at your paper's garment setting. Lay the garment flat and let it cool for at least 5 minutes. Peel only when it's completely cool, within 60 minutes, starting where toner coverage is heaviest. Uninet warns that peeling while it's still warm can leave an incomplete transfer.
-
Re-press for wash durability
Uninet says the re-press is required. Cover with kraft paper (or iColor T. Seal for a matte finish), press at your paper's re-press setting, wait 10 to 15 seconds before lifting the paper, then stretch the fabric lightly while it's still hot.
Only use kraft paper made for heat presses. Butcher paper and other papers can stick to the image. Never run the adhesive sheet through the printer.
Watch Uninet's video: Select 2 Step transfer paper
More videos
Embedded from the manufacturer's official channel.
Common questions
Which side of the transfer sheet do I print on?
It depends on the paper. On iColor Premium the smooth coated side is the print side, and the package is marked. On iColor Select the rough coated side is the print side. On the 560, load print side down in the bypass tray or print side up in tray 1.
Can I run the adhesive (B) sheet through the printer?
No. Uninet warns that running the adhesive sheet through the printer can ruin the fuser, and fuser damage from a jam isn't covered.
My image is on white cotton with no white in it. Do I still need white toner?
Yes. Uninet says white overprint is needed even on white garments, because it fills the halftones so the adhesive has enough toner to stick to.
The transfer cracks after washing.
Make sure you did the re-press (post press), which Uninet says is required for wash durability, and stretched the fabric lightly while hot. Wash inside out in cold or warm water, skip fabric softener and tumble dry low or hang dry.
My paper might be old. Does it go bad?
Humidity is the main enemy of the adhesive sheets. Store them sealed in a bag with a silica pack, and let new media reach room temperature before use. If fresh, dry sheets still fail with the settings below, text us photos of both sheets at (562) 609-4996.
- iColor Premium 2 Step Transfer Paper Instructions
- iColor Select 2 Step Transfer Paper Instructions
- iColor 560 User Manual, ProRIP Essentials version: printing tips
- AA support requests about iColor transfer paper not adhering, 2024 to 2026











































































