Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
iColor 800W setup and everyday use: toner slots (why Yellow means White), loading transfer media, banners and paper jams
On the iColor 800W the printer's screen still uses CMYK names, so read the messages through Uninet's table: Yellow low means replace the White toner, and Black low means replace the Yellow toner. Load transfer media face down in the bypass (multipurpose) tray until it beeps, or face up in Tray 1. For jams, follow the animation on the screen and the letter it shows, never pull out the fusing unit, and open and close the front cover if the message stays after the paper is out.
Where it goes
- The 800W weighs about 187 lb (85 kg). Lift the locks at the bottom of the box, unwrap it, and lift it out as a team.
- Leave about 4 inches (10 cm) clear on the sides. Uninet's install drawing shows the space it needs front to back.
- Keep the room between 50 and 89°F (10 to 32°C) and 15 to 80% humidity.
- Power: 120 to 127 V, 60 Hz, 12 A or more (or 220 to 240 V, 10 A).
First setup
-
Remove packing
Remove all the orange tape and packing material, including the orange security tape and lock inside the printer.
-
Open the toner compartment
Take the tape and packing out of the paper trays, close them, and open the main toner compartment.
-
Install the toners
Remove the rest of the orange tape and set the lock. Gently shake each toner cartridge back and forth 7 or 8 times to loosen toner that settled in shipping. Unscrew the toner lock and insert each cartridge in its matching slot, arrow on top. The slots run W, M, C, Y.
-
Power on
Close the toner compartment, plug in the power cord and switch the printer on.
-
Install ProRIP
The software and license are on the ProRIP USB dongle. See ProRIP install and activation. Don't lose the dongle: it is your license key, and Uninet charges to replace it.
Reading toner messages
The 800W comes with four toners for color plus white, but the printer's screen still uses CMYK names. Use Uninet's table every time a toner runs low.
| Screen says | Replace with |
|---|---|
| Cyan low or empty | Cyan |
| Magenta low or empty | Magenta |
| Yellow low or empty | White |
| Black low or empty | Yellow |
Always put toner and drum cartridges in the slot for their color. Uninet warns that the wrong slot can cause serious damage, and that non-genuine toner, drums, belts, fusers or registration parts can cause damage the warranty doesn't cover.
Black on the 800W is a composite made from cyan, magenta and yellow, which is why there is no black cartridge.
Loading transfer media
| Tray | How to load |
|---|---|
| Bypass tray | Suggested for transfer media. Face down until it beeps; slide the guides to the sheet. Up to 100 sheets, 3 x 5 to 12.6 x 49.6 inches |
| Tray 1 | Print side face up. Letter, A4 or A5. Load only a few sheets of transfer media, or it may feed several at once |
| Tray 2 | Adjustable up to 12 x 18 inches |
In the paper trays, make sure the media sits under the guides before closing, don't go above the upper limit mark, set the side and end fences to the size, and straighten any curled or warped sheets first. Push the tray fully in.
Banners
The 800W prints up to 49.6 inches long through the multipurpose tray. Uninet recommends the optional banner paper guide tray for higher volume. With it, you can load up to 10 banner sheets, but put them in as individual sheets, never as a stack, and set the paper guides flush so the image doesn't skew or misfeed. To close the banner tray, take out any paper, fold up the subtray, slide the guides out, fold up the banner guide tray, close the bypass tray slowly while supporting it, then turn the knob counterclockwise to the lock mark.
Clearing a paper jam
-
Find it
The screen shows an animation and a letter for where the paper is stuck. The sticker inside the front cover shows the same letters.
-
Take the paper out
Follow the animation. If the paper didn't go into the fusing section correctly, pull it out from underneath the fusing unit; if you can't, take it out from the top. Don't touch any part labeled hot surface, and don't remove the fusing unit, or print quality suffers.
-
Banner tray fitted?
Take the paper out of the bypass tray first, then open the right cover, so the loaded sheets don't fall out.
-
Clear every scrap
Torn scraps left inside cause more misfeeds. If the message stays after the paper is out, open the front cover fully and close it.
Uninet's tips for better transfers
- Uninet's instructions assume a Hotronix Fusion press and cotton garments. Clamshell and other presses, and other fabrics, may need small changes.
- Photos and full color graphics may need a longer press than vector art or text.
- Toner coverage under 70% can stop the adhesive transferring. Fix halftones with a white overprint in ProRIP.
- For the darkest black, use 100C, 100M, 90Y.
If ProRIP can't find the printer, see iColor not connecting. If transfers won't stick, see iColor transfer paper not adhering. For anything else, Text us a photo or short video at (562) 609-4996.
Common questions
The printer says Yellow is low, but my yellow toner is nearly full. What do I replace?
The White toner. Uninet's table: Cyan means Cyan, Magenta means Magenta, Yellow means White, and Black means Yellow.
Which tray should I use for transfer paper?
Uninet suggests the bypass tray. Load the media face down until you hear a beep and slide the guides against it.
How long a banner can it print?
Up to 12.6 x 49.6 inches through the multipurpose tray. Uninet recommends the optional banner paper guide tray for regular banner work, although banner media can be fed by hand.
Why is my transfer patchy where the image has light areas?
Uninet says toner coverage should not be less than 70%, or the adhesive won't transfer properly. Halftones can be fixed by printing white on top of the color in ProRIP, in one pass.
My blacks look brown. What should I use?
Uninet suggests setting rich black to 100C, 100M, 90Y to avoid brownish or yellowish black.
- iColor 800W User Manual (February 2020 edition)
- Uninet iColor support and knowledge base
- AA support requests about iColor printers, 2024 to 2026










































































