Support
Machine type
Brand
Uninet iColor white toner transfer printers (560, 650, 800W and earlier models)

iColor T. Seal finishing sheet: how to use it and why it won't seal

✓ Reviewed by Jason KimUpdated 2 min readFits: iColor 560 · 650 · 550 · 800 · 600 · 500
Short answer

T. Seal replaces kraft paper for the final post press only. Condition a new sheet once (rubber side down, 20 seconds, medium pressure, 270°F). After you press and peel your transfer as its paper directs, cover it with the rubber side down and press 20 seconds at heavy pressure, 270 to 290°F. Wait 5 seconds, then peel slowly. Never go above 300°F, never cut the sheet, and don't use it with CP toner or sublimation.

T. Seal is a paper carrier with a thin silicone rubber film. On the final post press, the film pushes the image down into the weave, which Uninet says gives the best wash and stretch durability. It works with any iColor transfer paper or foil, and it replaces kraft paper on that last press only.

Quick reference

What Uninet's setting
First use only (conditioning) Empty press, rubber side down, 20 seconds, medium pressure, 270°F / 132°C
Final post press Rubber side toward the decoration, 20 seconds, heavy pressure, 270 to 290°F / 132 to 143°C
Peel Wait 5 seconds after opening, then peel slowly
Maximum temperature 300°F / 150°C
Life 350 to 500 presses
Not for CP toner, sublimation ink or toner, sublimated items, the first transfer press

Condition a new sheet (once)

  1. Press it empty

    Before the first use, lay the sheet rubber side down on the lower platen of your heat press and press it for 20 seconds at 270°F (132°C) with medium pressure. Nothing else goes in the press.

Every transfer

  1. Apply the transfer as normal

    Press and peel your transfer exactly as the instructions for your paper say, with the cover sheet they call for.

  2. Post press with T. Seal

    Lay the T. Seal over the decoration with the rubbery side down toward it. Press for 20 seconds at heavy pressure, between 270 and 290°F (132 to 143°C).

  3. Wait, then peel slowly

    Open the press, wait 5 seconds, then peel the sheet off slowly.

Never use T. Seal above 300°F (150°C): it degrades early. Don't use it with CP toner, sublimation ink or toner, or on sublimated items.

If it doesn't seal or misbehaves

What you see Check
Transfer doesn't look sealed into the fabric Was the sheet conditioned? Pressure heavy, time 20 s, temperature 270 to 290°F? Rubber side facing the decoration?
Toner sticks to the T. Seal Wait the full 5 seconds before peeling, then peel slowly
Rubber film peeling or coming apart The sheet was cut, overheated past 300°F, or has reached the end of its 350 to 500 presses
Yellow staining in the film CP toner was used with it. Keep that sheet away from iColor transfers.
Transfer itself won't stick to the shirt That happens at the first press, before T. Seal. See our guide to iColor transfer paper not adhering.

Get the most presses out of it

Because the sheet is rated for 350 to 500 presses, note the date you conditioned it and keep a rough count. When the film starts to lift or the finish stops looking even, it's time for a new sheet. Keep it flat and whole: Uninet warns that cutting it makes the rubber film come apart, so buy the size that covers your designs instead of trimming a bigger one.

Seeing marks or texture on the shirt you didn't expect? Text us a photo of the shirt and your press settings at (562) 609-4996, and tell us which transfer paper you used.

Common questions

Do I use T. Seal for the first press?

No. Uninet says it's for the final post press only. Press and peel the transfer with the cover sheet its own instructions call for, then post press with T. Seal.

How many times can I use one sheet?

Uninet rates it for 350 to 500 presses.

Can I cut it to fit a small press?

No. Uninet warns the rubber film comes apart if the sheet is cut.

The sheet turned yellow. Why?

Uninet says CP toner's yellow pigment migrates into the rubber film, so don't use T. Seal with CP toner. It's also not for sublimation inks, toners or sublimated items.

Some toner stuck to the T. Seal. What happened?

Uninet's instructions call for waiting 5 seconds after opening the press and then peeling slowly. Peeling right away or fast pulls toner.

Sources
Did this fix it?