Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex D-100 and D-1000 dryer assembly: building the chamber, wiring the heater and fitting the belt
Build the chamber panels around the heater (wires to the back), set it into the conveyor cutouts, then with the cord unplugged feed the two tan heater wires and the green ground through the bed. Push the tan wires onto the heat control terminals and bolt the ground to its stud. Thread and pin the belt, raise the aligner about 1 1/2 in, track it, and fit the chain and belt guards before first power.
The D-100 conveyor ships in one piece. The D-1000 conveyor comes in two halves. Use a 1/4 in nut driver (or socket) and a 7/16 in wrench. Vastex supplies flat plate wrenches in both sizes. Don't overtighten the sheet metal screws.
D-1000 only: join the conveyor
Slide the two halves together so the inner and outer joiner plates interlock, and fit six screws on each side.
Build the chamber
-
Height knobs
On each side panel, fit the knob and bolt through the pointer and spacer from the outside, into the weld nut and hex nut on the inside.
-
Panels
Attach the front panel, then the back panel, to the left side panel, then both to the right side panel, with three sheet metal screws at each corner.
-
Heater
Install the heater with its wires toward the back of the chamber, using the four heater mounting pins (two each side). Check the pins are in before you go on.
Mount the chamber and wire the heater
-
Set it on the conveyor
Slide the chamber's corner tabs into the cutouts in the conveyor, heater wires toward the back, and attach it with three screws each side.
-
Feed the wires through
With the power cord unplugged and the belt off, pass the three heater wires one at a time through the hole in the conveyor bed: the two tan wires first, then the green.
-
Lay the conveyor on its side
Carefully tip the dryer onto its side so you can reach the controls underneath.
-
Connect the heater wires
Push each tan wire's connector onto either open terminal on the heat control. It doesn't matter which goes where. They should be hard to push on; tug gently to check each one is held firmly.
-
Connect the ground
Remove the wing nut and lock washer from the grounding stud, put the green wire's ring terminal on, and refit the lock washer and wing nut tightly. Push any slack wire back up through the hole.
Fit the belt
-
Thread it
With the dryer still on its side, pass the belt over the aligner bar and both braces. Then set the dryer back on its feet.
-
Join it
Line up the belt edges and push the connecting pin through. You can trim the pin ends.
-
Tension it
Center the belt on both rollers and raise both sides of the aligner equally, about 1 1/2 in. Tension only enough to stop the belt slipping on the drive pulley.
-
Track it
On a flat surface, run the belt at full speed and watch both rollers. Raising one side of the aligner moves the belt the other way. Make 1/4 turn adjustments and give the belt time to respond. Never let it run off the rollers, and don't leave it unattended.
Finish up
-
Tidy the wires
Pull gently up on the wires to take excess out from under the bed. Secure them with the high temperature tie wrap and trim it.
-
Covers
Position the wires behind the wire cover and fit it with two screws. Fit the top cover with its screws.
-
Guards
Hook the chain guard's bottom tabs into the slots below the drive chain, pivot it up and secure it. Fit a belt guard on each side at the rear of the conveyor with two screws each. Never run the dryer with the chain guard off.
Power it
The 120 V D-100 needs a dedicated 15 A circuit with a new commercial-duty NEMA 5-15R receptacle; the 120 V D-1000 needs a dedicated 20 A circuit with a 5-20R. The 240 V versions need a good quality 6-15R. Then follow our D-100 and D-1000 start-up and cure settings guide: belt on first, then heat.
Text us a photo or short video at (562) 609-4996 if a connection or part doesn't match.
Common questions
Does it matter which tan wire goes on which terminal?
No. Vastex says either heater wire can go on either open terminal of the heat control. Just make sure each push-on connector is fully seated and tight.
The connectors are very hard to push on.
That is intended. Vastex wants a tight connection. Push firmly until fully seated, then tug gently to check.
Can I run it without the belt to test the heat?
No. Vastex says not to operate the dryer without the belt installed, and the belt must be moving whenever the heater is hot.
Can I add length to a D-1000?
Yes, Vastex sells a 10 in extension. With power disconnected, remove the chamber and belt, separate the conveyor halves, fit the extension between them, splice in the belt extension piece and reassemble.
What outlet does the D-100 need?
The 120 V model needs a dedicated 15 A circuit with a new commercial-duty NEMA 5-15R receptacle. The D-1000 needs a dedicated 20 A circuit with a 5-20R.
- Vastex D-100 and D-1000 assembly and operating instructions, doc 01-23-001E
- AA support requests about Vastex dryers, 2024 to 2026










































































